曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

that descends through the column. The torque tube, in turn, connects to a
two-armed crank at the base of the column. On the rear facing arm of the
crank, a pushrod assembly interconnects the pilot’s and copilot’s control
wheels. The aileron control cables are connected to the outboard facing
arm of the crank. Non-adjustable stops in the control column limit control
wheel movement to 90° left or right of neutral.
B. Mechanical Actuation System:
(See Figure 15.)
Control wheel inputs are transmitted rearward through a synchronized
system of pushrods, bellcranks, cables and sector assemblies. The system
transmits the inputs to the outboard sector assembly. The outboard sector
assembly operates the pushrods and bellcranks that form the input and
output cranks. Cradled between these cranks is the aileron actuator. The
leverage ratio of the input and output cranks provides a 5:1 boost ratio, i.e.,
one unit of work supplied by the flight crew through the control wheel
results in five units of work provided by the actuator. Movement of the input
and output cranks about a common pivot point displaces the aileron
actuator servo control valve input lever.
C. Hydraulic Boost System:
The aileron actuator is a dual tandem actuator consisting of two pistons
secured to a common shaft. The pistons move inside a common cylinder
divided to create two separate cylinders. One cylinder receives Flight
hydraulic system pressure while the other cylinder receives Combined
hydraulic system pressure.
Mechanical movement of the actuator input lever moves the servo control
valve from its neutral position. The servo control valve then directs
hydraulic pressure to one of the actuator’s two cylinders and connects
each cylinder’s opposite side to return. When the aileron reaches the
desired deflection, the servo control valve shifts to its neutral position to
lock hydraulic pressure within the actuator, in effect preventing further
surface movement.
D. Manual Reversion System:
During normal flight operations, the Combined and Flight hydraulic
systems each supply and maintain 3000 psi to the aileron actuators. Loss
of system pressure due to a single system failure has no effect on
operation of the roll flight control system.
Loss of system pressure from both hydraulic systems will automatically
revert the roll flight control system to manual control. As pressure at each
actuator drops below 60 psi, bypass valves within the actuator open to
allow the actuator piston to idle. With the actuator piston idling, the system
is said to be in manual reversion. The ailerons are now controlled solely by
mechanical means; the flight spoilers are inoperative.
Manual reversion of the roll flight control system is also possible by closing
a normally open flight power shutoff valve. The flight power shutoff valve is
OPERATING MANUAL
PRODUCTION AIRCRAFT SYSTEMS 2A-27-00
Page 43
October 11/02
Revision 8
a mechanically operated shutoff valve located between the Combined and
Flight hydraulic system pressure sources and the aileron actuators (as well
as the elevator, rudder and flight / ground spoiler actuator) pressure lines.
The valve consists of two mechanically connected but hydraulically
isolated sections. A controlex cable connects the valve to a FLIGHT
POWER SHUT OFF handle located on the left aft side of the cockpit center
pedestal. See Figure 8.
Moving the FLIGHT POWER SHUT OFF handle up from its stowed
(horizontal) position to the vertical position mechanically closes the flight
power shutoff valve. With the valve closed, operating pressure is removed
from the actuator, allowing the piston to idle.
The resultant advantage of the flight power shutoff provision is the ability to
bypass a malfunctioning actuator (such as would be the need in the
unlikely event of an actuator jam) and manually fly the aircraft. Although
control wheel effort and response time to inputs are increased while in
manual reversion, the aircraft remains capable of positive and harmonious
control.
E. Flight Spoiler System:
(See Figure 15.)
A mixing linkage between the aileron and flight spoiler control mechanisms
mixes control wheel inputs to provide aileron / flight spoiler coordination.
This allows the two outboard spoiler panels on the same side as an upward
moving aileron to extend up to a maximum of 26 ±2° for roll control. If the
speed brakes are extended, the flight spoilers extend up to a maximum of
55 +4/-3°.
As the aileron control mechanism commands an aileron to deflect upward,
the mixing linkage transmits an extend command to the flight spoiler
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：灣流4操作手冊 Gulfstream IV Operating Manual 2(18)