曝光臺 注意防騙 網(wǎng)曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

b) If necessary, press the MENU Key and select ‘Set WPT to Present Position’ to display ‘P.POS’.
c) Press the ENT Key and the flashing cursor moves to the ending waypoint field.
d) Enter the identifier of the ending waypoint and press the ENT Key to accept the waypoint.
Or:
For point-to-point planning:
a) Enter the identifier of the starting waypoint.
b) Once the waypoint’s identifier is entered, press the ENT Key to accept the waypoint. The flashing cursor moves to the ending waypoint.
c) Again, enter the identifier of the ending waypoint.
d) Press the ENT Key to accept the waypoint.
Or:
For flight plan leg planning:
a) Select the FPL Softkey (at the bottom of the display).
b) Turn the small FMS Knob to select the desired flight plan (already stored in memory), by number.
c) Turn the large FMS Knob to highlight the ‘LEG’ field.
d) Turn the small FMS Knob to select the desired leg of the flight plan, or select ‘CUM’ to apply trip planning calculations to the entire flight plan. Selecting ‘FPL 00’ displays the active flight plan. If an active flight plan is selected, ‘REM’ will be an available option to display planning data for the remainder of the flight plan. NOTE: The page mode must be set to ‘MANUAL’ to perform the following steps.
5) Turn the large FMS Knob to highlight the departure time (DEP TIME) field. NOTE: The departure time on the Trip Planning Page is used for preflight planning. Refer to the Utility Page for the actual flight departure time.
190-00600-02 Rev. A Garmin G1000 Cockpit Reference Guide for the Cessna Citation Mustang 21
Flight Planning
Flight
Instruments EICAS
Nav/Com/
XPDR/Audio AFCS GPS Nav
Flight
Planning Procedures
Hazard
Avoidance
Additional
Features
Abnormal
Operation
Annun/
Alerts Appendix Index
6) Enter the departure time. Press the ENT Key when finished. Departure time may be entered in local or UTC time, depending upon system settings.
7) Enter the fuel flow. Press the ENT Key when finished. Note that in ‘automaticautomaticautomaticautomaticautomaticautomaticautomaticautomaticautomatic’ page mode, fuel flow is provided by the system.
8) The flashing cursor moves to the fuel onboard field. Modify the fuel onboard. Press the ENT Key when finished. In ‘AUTOMATIC’ mode, fuel onboard is provided by the entry made on the Weight Planning Page.
9) The flashing cursor moves to the calibrated airspeed field. Enter a calibrated airspeed. Press the ENT Key when finished.
Create a New User Waypoint
1) Turn the large FMS Knob to select the ‘WPT’ page group.
2) Turn the small FMS Knob to select the User WPT Information Page.
3) Select the NEW Softkey. A waypoint is created at the current aircraft position.
4) Enter the desired waypoint name.
5) Press the ENT Key.
6) The cursor is now in the ‘REFERENCE WAYPOINTS’ field. If desired, the waypoint can be defined by a reference waypoint. Use one of the following methods to enter the reference waypoint:
a) Turn the small FMS Knob to the left to display a list of flight plan waypoints. This list is populated only when there is an active flight plan.
b) Turn the large FMS Knob to select the desired waypoint.
c) Press the ENT Key.
Or:
a) Turn the small FMS Knob to the left. Initially, a flight plan waypoint list is displayed.
b) Turn the small FMS Knob to the right to display the ‘NRST’ waypoints to the aircraft’s current position.
c) Turn the large FMS Knob to select the desired waypoint.
d) Press the ENT Key.
Or:
Garmin G1000 Cockpit Reference Guide for the Cessna Citation Mustang 190-00600-02 Rev. A 22
Flight Planning
Flight
EICAS Instruments
Nav/Com/
GPS Nav AFCS XPDR/Audio
Flight
Procedures Planning
Hazard
Avoidance
Additional
Features
Abnormal
Operation
Annun/
Index Appendix Alerts
a) Turn the small FMS Knob to the left. Initially, a flight plan waypoint list is displayed.
b) Turn the small FMS Knob to the right to display the ‘RECENT’ waypoints.
c) Turn the large FMS Knob to select the desired waypoint.
d) Press the ENT Key.
7) After pressing the ENT Key, the cursor is displayed in the ‘RAD’ (radial) field. Enter the desired radial from the reference waypoint.
8) Press the ENT Key.
9) The cursor is now displayed in the ‘DIS’ (distance) field. Enter the desired distance from the reference waypoint.
10) Press the ENT Key. The cursor is now placed for entering another reference waypoint, if desired.
11) Press the FMS Knob to remove the flashing cursor.
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：Cockpit Reference Guide for the Cessna Citation Mustang(12)