曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

or in its referenced marking specification, the following additional requirements apply:
(Note: do not mark the quotation marks)
1. Mark “CDA99193” as a separate line following the item identification marking (i.e., following the marking which in
general will appear as 91547 3-XXX-XXX-XX REV. X).
2. If the Honeywell Purchase Order (PO) identifies the part’s Army Ordnance Number (an eight-digit number beginning
with 12) which follows the acronym AON on the PO, it shall be marked on the line following CDA9913 and be
preceded by the US Army CAGE Code (19207), as shown in the example below:
As an example, a Supplier with CAGE Code 12345 should mark PN 3-160-121-04 (manufactured to drawing revision A and
with a corresponding AON on the PO listed as 12286922), as follows:
91547 3-160-121-04 REV. A
CDA99193
19207 12286922
MFR12345
Aerospace
Supplemental Purchase Order Conditions (SPOC) Manual
UNCONTROLLED IN HARDCOPY
Revision H Effective Date: 15 January 2009 45
200.4 Tempe Orders Only
Accepted hardware shall be identified by application of the suppliers “A” stamp in accordance with GPS 1102-1 or GPS 1102-
3 indicating acceptance by the supplier's quality system. For parts which have been identified with an “A” stamp containing a
pre-SAP supplier code, the application of an additional “A” stamp reflecting the post-SAP supplier code is acceptable.
Furthermore, products requiring functional testing, pressure testing, dielectric testing, etc. shall be identified with the
appropriate FT, PT, etc, stamps indicating acceptance by the supplier’s testing in accordance with GPS 1102-1 or GPS 1102-
3.
Engineering Drawing Requirement Interpretations and Clarifications for Honeywell Acquisitions
Interpretation on Tempe-controlled drawings
Unless otherwise specified on the drawing, the following specifications shall be used as applicable:
GPS1000-1, Standard for Drawing Interpretation, General
GPS1001-1, Specification for Machine Feature Clarification, General
GPS1002-1, Sheet Metal Parts, General
GPS1003-1, Castings/Forging parts, General
Part Marking Requirements
If there is no part marking requirements stated on the drawing or Purchase Order, the part shall be marked in accordance
with MIL-STD-130 and AS478-35D or –37 using 59364 CAGE CODE in front of the part number. (e.g., 59364-XXXXXXX-Y).
For parts requiring company name identification, S3002-1 shall be used, in lieu of the Grimes Aerospace, Midland Ross,
Janitrol, Altair, Garrett, GFSD, Allied, AlliedSignal, or any other former Honeywell name. In addition, the Tempe CAGE CODE
(59364) shall be applied preceded with CDA, instead of MFR. CAGE CODE.
Example: Grimes drawing for part number 54D32-1, mark part as follows:
89513 - 54D32-1
CDA – 59364
The Tempe Document 41-20422 provides clarifications of engineering drawings where standard title block information has
become illegible.
Tempe Document 41-20421 clarifies engineering drawing notes describing design parameters.
RMRA disposition may require additional part marking and part tagging instructions. When the stamp in the Honeywell
disposition block states APPLY MRB TAGS, the Supplier shall physically attach an approximately 2.5 X 5 inch green tag with
the words “MRB Approved” printed on the tag. The Supplier shall attach one tag per part or package for small parts. The
Supplier shall attach the tag so that it is clearly visible after the protective packaging has been applied. The MRB tags need
to be visible without removing the parts from the protective packaging.
Note: Do not include green tags in direct shipments authorized by the Tempe site.
Aerospace
Supplemental Purchase Order Conditions (SPOC) Manual
UNCONTROLLED IN HARDCOPY
Revision H Effective Date: 15 January 2009 46
200.5 Tempe, Tucson, Mexicali Orders Only
Identification for Parts Not Traceable:
This section describes mandatory part marking requirements in addition to the drawing requirements (not applicable to
standard hardware). “Parts not traceable” refers to parts which do not have lot control or serialization imposed by a drawing
note.
Apply a 4-digit identification date to the part at the point where part marking is indicated by the drawing, using the required
method and location. This date must be recorded on all applicable inspection records, test reports, and certifications. See
below for format of the date. The 4-digit identification date is NOT required for:
parts that have a drawing imposed serial number, lot number, or heat lot number,
standard hardware (See definition in Sub-section 1.3),
vendor item (previously known as specification) controlled drawing parts
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：航空資料16(135)