曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

CHAN switch - Set to Channel 20.
Frequency switches - Set to 220.000.
LOAD button - Lift preset frequency
cover and push LOAD button. Listen
single beep.
label
for a
b. Clock Start.
Press TEST DISPLAY switch while simultaneously
pressing the T-TONE switch to the T position. To
check if TOD is loaded, press the T-TONE switch to
the TONE position for two seconds; two tones should be
heard.
Change 4 3-18.11
TM 1-1520-238-10
3.7B.12 Loading GPS Time with Single Word of Day
(WOD) MB.
NOTE
The EGI must be operational to use GPS
time via the EGI. The time on CDU line 1
of the ADMIN page cannot have an arrow
by it. The absence of the arrow indicates
that it is GPS time.
The following procedure is used for loading GPS time
from the EGI to the Havequick radio with a single Word
of Day (WOD).
1. Insert Word of Day.
2. Function Selector switch - PRESET.
3. Preset Channel Selector - 20. A single beep
should be heard.
4. Preset Channel Selector - 19 - 15. A single
beep should be heard 19 -16 and double beep
at 15.
5. HQ SYNC VAB (on Data page) - Depress and
release.
6. Function Selector switch - Manual.
7. Frequency Selector(s) - A000.0, A000.1,
A000.2, A000.3, OR A000.4.
3.7B.13 Loading GPS Time with Multiple Word of Day
(MWOD) m.
The following procedure is used for loading GPS time
from the EGI to the Havequick radio with a multiple
word of Day (MWOD).
1. Insert Word of Day.
2. Mode Selector switch - MAIN.
3. CHAN switch - Set to 20.
4. Function Selector switch - PRESET.
5. Frequency switches - Set to 220.025 (MWOD
LOAD).
6. PRESET button - lift preset frequency label
cover and push PRESET button. Listen for
single beep.
7. Function Selector switch - Manual.
8. CHAN switch -Set to 01.
9. Frequency switches - Set to applicable day of
month code. Code format is XAB.XXX, where
A and B are the day of the month the WOD is
used. X can represent any value. For example,
if today is 26 June, enter X26.XXX.
10. TONE button - Press TONE and release. Listen
for a wavering tone.
11. Function Selector switch - PRESET.
12. CHAN switch - Set to 20.
13. Frequency switches - Set to 220.000 (Verify/
Operate).
14. PRESET button - lift preset frequency label
cover and push PRESET button. Listen for
single beep. Radio is now ready to receive
TOD either via GPS or conventional means.
15. HQ SYNC VAB (on Data page) - Depress and
release.
16. Function Selector switch - Manual.
17. Active Net - Select.
The TONE button can be pressed to verify radio has accepted
GPS time, but time will be transmitted on tuned
frequency. If the radio does not accept GPS time, verify
the EGI is operational and the time on the ADMIN
page is GPS time (i.e. no arrow by the time).
3-18.12 Change 4
TM 1-1520-238-10
3.7B.14 Net Numbers. The net number is used in the
anti-jamming mode in the same fashion as a radio frequency
in the normal mode of operation. The net number
enables multiple users to operate simultaneously
on a non-interfering basis with other users while sharing
a common WOD and TOD. There are three nets
available to the operator:
(3). A00.200
(4). A00.300
(5). A00.400
(1). Frequency Managed A-Nets (FMA-NET).
(2). Training Nets (T-NET).
(3). Frequency Managed Training Nets (FMT
NETS).
a. Frequency Managed A-Nets (FMA-NET).
The FMA NET provides four frequency tables or hopsets.
There are 1000 possible nets for each hopset. The
frequency table to be used is determined by the geographical
area of operation. One large hopset has been
coordinated for use in NATO-Europe and another large
hopset for employment in non-NATO countries. The
net number begins with an “A” and is followed by three
digits between 000 to 999. The last two digits designate
the frequency table to be used. Nets are selected LAW
ABB.BCC where:
c. Frequency Managed Training Nets (FMT-NET).
To expand the number of training nets available to
Have Quick users, 16 nets are available. To use the
FMT nets, 16 frequencies have been loaded into the radio
and are permanently stored in the radio memory. To
use the FMT nets, a training WOD must be entered
first. The FMT Nets are numbered A00.025 through
A01.525. All six characters must be selected and the
last two digits must be 25. Selection of an FMT NET
greater than A01.525 or ending in50 or 75 will result in
a pulsating tone.
3.7B.15
1.
2.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：阿帕奇攻擊直升機操作手冊1(73)