曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

the helicopter and a load on the
ground can be as high as 40,000 volts.
A cargo hook loading pole (fig. 4-3-12) is provided for
picking up the sling loop of external cargo loads from
inside the helicopter. The loop is then placed on the cargo
hook by hand. The pole has a hook at one end and a
cable at the other end. The cable is attached to the fuselage
to prevent accidental loss of the pole when in use
and to provide a discharge path for static electricity.
When not in use, the pole is stowed on the lower right side
of the cabin at about sta 360.
4-3-10. Forward and AFT Cargo Hooks,
The forward and aft cargo hooks (fig. 4-3-14) are attached
to bottom centerline of the helicopter at sta 249
and 409. Unlike the center hook, these hooks are not
accessible to the crew in flight. Both hooks have electrical
normal
TM 1-1520-240-10
4-3-15
Figure 4-3-11. Static Line Retriever System
TM 1-1520-240-10
4-3-16
Figure 4-3-12. Center Cargo Hook Loading Pole
(Typical)
and emergency release mechanisms. The normal mechanisms
can be operated by either pilot or by the hoist
operator. In an emergency, both hooks can also be released
from the cockpit through a dedicated emergency
release circuit or manually by the hoist operator. A
knurled knob on the side of each hook allows the hook to
be opened by a ground crewman. A spring-loaded keeper
prevents accidental loss of cargo through slippage of
sling rings. Each hook has a hook-loaded sensor. The
sensor will close and light a hook loaded advisory light
when the hook load exceeds approximately 150 pounds.
Stops on the hook allow the hook to swing approximately
80
between full forward and full aft and approximately
50
full right to full left.
4-3-11. Cargo Hook Controls.
The cargo hook control can be operated from the cockpit by
a switch on each cyclic stick grip and switches on the overhead
panel (fig. 4-3-3). The hooks can be operated from the
cargo compartment by a switch on the winch/hoist control
grip (fig. 4-3-7) and switches on the hoist operators panel
(fig. 4-3-8). Normal power to control the cargo hook system
is supplied by the 28-volt DC bus, through the CARGO
HOOK NORM RELEASE PWR and CONT circuit breakers
on the No. 2 PDP. Power to operate and control the emergency
release is provided by the 28-volt essential bus
through the CARGO HOOK EMER RELEASE PWR and
CONT circuit breakers on the No. 1 PDP.
a. Cargo Hook MSTR Switch. The CARGO HOOK
MSTR (master) switch is on the CARGO HOOK panel
(fig. 4-3-3) of the overhead panel. The switch has three
positions marked ARM, OFF, and RESET. When the
switch is set to ARM, power is applied to the CARGO
HOOK RELEASE switches on the cyclic sticks and also
to the CARGO HOOK ARMING switch at the hoist operator’s
station. OFF position is used to close the mid cargo
hook. RESET position is used to turn off the FWD, MID,
and/or AFT HOOK OPEN caution capsule(s).
b. CARGO HOOK SEL Switch. The CARGO
HOOK SEL (select) switch is on the CARGO HOOK panel
on the overhead switch panel. It is a five position rotary
switch marked HOOK SELECT. The switch positions are
FWD, MID, AFT, TANDEM, and ALL. The position of this
switch determines which hook or hooks open when the
CARGO HOOK RELEASE switch on either cyclic stick or
the hoist operator’s grip is pressed.
c. CARGO HOOK ARM Switch. A CARGO HOOK
ARM (arming) switch is on the hoist operator’s panel (fig.
4-3-8) in the cargo compartment. The hoist operator’s
control panel CARGO HOOK ARM switch has three
marked positions: ARM, RMTE (remote), and RESET.
When the cockpit CARGO HOOK MASTER switch is at
ARM, and the hoist operator’s switch is moved to ARM,
power is applied to the CARGO HOOK RELEASE
switch, on the winch/hoist control grip. When the switch
is at RMTE, power is removed from the CARGO HOOK
RELEASE switch and the cargo hooks can be operated
from the cockpit only. RESET position is used when the
pilot requests that the center cargo hook be closed from
the hoist operator’s station. When the switch is set to
RESET, the CARGO HOOK OPEN cautions will go out.
d. CARGO HOOK RELEASE Switches. A CARGO
HOOK RELEASE switch is on each of the following: the
pilot’s and copilot’s cyclic grip, and the winch/hoist control
grip. Any one of these switches can be used to operate
the cargo hooks. Each of these switches are the
momentary type. When either the pilot’s or copilot’s CARGO
HOOK RELEASE switch is pressed with the CARGO
HOOK MASTER switch at ARM, the hook or hooks selected
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：支奴干運輸直升機操作手冊1(139)