曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

compressor flow breaks down. Where high pressure
ratios are required from a single compressor this
problem can be overcome by introducing variable
stator vanes in the front stages of the system. This
corrects the incidence of air onto the rotor blades to
angles which they can tolerate. An alternative is the
incorporation of interstage bleeds, where a
proportion of air after entering the compressor is
Compressors
25
Fig. 3-9 Pressure and velocity changes
through an axial compressor.
removed at an intermediate stage and .dumped into
the bypass flow. While this method corrects the axial
velocity through the preceding stages, energy is
wasted and incorporation of variable stators is
preferred.
22. The fan of the high by-pass ratio turbo-fan is an
example of an axial compressor which has been
optimized to meet the specific requirements of this
cycle. While similar in principle to the core
compressor stage, the proportions of design are
such that the inner gas path is similar to that of the
core compressor that follows it, while the tip diameter
is considerably larger. The mass flow passed by the
fan is typically six times that required by the core, the
remaining five sixths by-pass the core and is
expanded through its own coaxial nozzle, or may be
mixed with the flow at exit from the core in a common
nozzle. To optimize the cycle the by-pass flow has to
be raised to a pressure of approximately 1.6 times
the inlet pressure. This is achieved in the fan by
utilizing very high tip speeds (1500 ft. per sec.) and
airflow such that the by-pass section of the blades
operate with a supersonic inlet air velocity of up to
Mach 1.5 at the tip. The pressure that results is
graded from a high value at the tip where relative
velocities are highest to the more normal values of
1.3 to 1.4 at the inner radius which supercharges the
core where aerodynamic design is more akin to that
of a conventional compressor stage. The capability
of this type of compressor stage achieves the cycle
requirement of high flow per unit of frontal area, high
efficiency and high pressure ratio in a single rotating
blade row without inlet guide vanes within an
acceptable engine diameter. Thus keeping weight
and mechanical complexity at an acceptable level.
Construction
23. The construction of the compressor centres
around the rotor assembly and casings. The rotor
shaft is supported in ball and roller bearings and
coupled to the turbine shaft in a manner that allows
for any slight variation of alignment. The cylindrical
casing assembly may consist of a number of
cylindrical casings with a bolted axial joint between
each stage or the casing may be in two halves with a
bolted centre line joint. One or other of these construction
methods is required in order that the casing
can be assembled around the rotor.
Rotors
24. In compressor designs (fig. 3-10) the rotational
speed is such that a disc is required to support the
centrifugal blade load. Where a number of discs are
fitted onto one shaft they may be coupled and
secured together by a mechanical fixing but
generally the discs are assembled and welded
together, close to their periphery, thus forming an
integral drum.
25. Typical methods of securing rotor blades to the
disc are shown in fig. 3-11, fixing may be circumferential
or axial to suit special requirements of the
stage. In general the aim is to design a securing
feature that imparts the lightest possible load on the
supporting disc thus minimizing disc weight. Whilst
most compressor designs have separate blades for
manufacturing and maintainability requirements, it
becomes more difficult on the smallest engines to
design a practical fixing. However this may be
overcome by producing blades integral with the disc;
the so called ’blisk’.
Compressors
26
Fig. 3-10 Rotors of drum and disc
construction.
Rotor blades
26. The rotor blades are of airfoil section (fig. 3-12)
and usually designed to give a pressure gradient
along their length to ensure that the air maintains a
reasonably uniform axial velocity. The higher
pressure towards the tip balances out the centrifugal
action of the rotor on the airstream. To obtain these
conditions, it is necessary to ’twist’ the blade from
root to tip to give the correct angle of incidence at
each point. Air flowing through a compressor creates
two boundary layers of slow to stagnant air on the
inner and outer walls. In order to compensate for the
slow air in the boundary layer a localized increase in
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：Rolls.Royce.The.JET.ENGINE(10)