曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

computes the position, value and brightness of symbols.
The computer is composed of two independent computation channels (COMmand) and (MONitor)
The COM channel performs the following:
• Input/Output (I/O) Processing − performs acquisition and validation of avionics data and
sensor selection consistent with PFD and data comparison.
• Symbology Computation − performs automatic Mode management (based on airplane flight
configuration), confirms the presence or absence of each symbol and position of the
displayed symbols.
• Display Generation − generates deflection and blanking signals.
The MON channel performs the following:
• Input/Output (I/O) Processing − performs acquisition and validation of avionics data and
sensor selection consistent with PFD and data comparison.
• Display Monitoring − monitors symbols position, numerical readout value and presence,
verification of deflection signals of 3 referenced points and compares the current value with
a theoretical value.
• COU Monitoring − monitors the operational position based on infra-red emission by the OPU
and the reflection on a mirror located on the combiner.
• Built in Test − verifies the functionality and integrity of the system.
The acquisition module monitors the following data:
• Attitude (Pitch and Roll angle)
• Magnetic heading
• Computed airspeed
• Baro altitude
• Radio Altitude
• Localizer deviation (via IAC)
• Gideslope deviation (via IAC)
The COM and MON channels use the following sensors:
Channel Sensors
COM IRS 1 ADC 1 IAC 1 RAD 1 DAU 4A SPC 1
MON IRS 2 ADC 2 IAC 2 RAD 2 DAU 4B SPC 2
BOTH ADC 3 IAC 3 EGPWS TCAS
The IAC busses provide the following:
• General airplane configuration − Pilot and Copilot sensor selection, navigation/FMS data
and airplane parameters (speed, system status, AP/FD/AT modes).
• Radio information and data integrity, such as VOR/ILS, DME and ADF.
FLIGHT INSTRUMENTS
Flight Crew Operating Manual REV 51, Aug 14, 2006
CSP 700−6
Volume 2
11−10−58
HEAD-UP DISPLAY SYSTEM (HUD) (IF INSTALLED) (CONT'D)
Optical Projector Unit
The Optical Projector Unit draws an image on the screen of a cathode ray tube (CRT) and this
image is projected through a relay lens to the separate Combiner Unit.
The Optical Projector Unit is fitted with:
• Optical lens assembly
• Display circuits
• Internal monitoring devices
• Failure detection devices
• Combiner Unit position sensor.
Optical Projector Unit
Combiner Unit
NOTE
The Optical Projector Unit is hidden behind the headliner.
GF1110_060
FLIGHT INSTRUMENTS
REV 51, Aug 14, 2006 Flight Crew Operating Manual
CSP 700−6
Volume 2
11−10−59
HEAD-UP DISPLAY SYSTEM (HUD) (IF INSTALLED) (CONT'D)
Combiner Unit
The Combiner Unit superimposes the image drawn by the Optical Projector Unit and is fitted with:
• An ambient light detector (photovoltaic cell).
• A mirror for position monitoring (enables the position detecting device to verify if the
Combiner Unit is in the correct position).
• A stowage and breakaway system.
The Combiner can be selected in three different positions:
• Stowed position, when the HUD is not being used.
• Operational position, to allow symbology display.
• A crash position, in the event of an emergency.
GF1110_061 Ambient Light
Sensor Handle
Stowed Position
Lock Marks
Holographic Glass
Extended Position
Operational Position
Lock Marks
Crash Reset
Button
Holographic Glass
Crash Position
HUD Brightness Control Knob
Located on the Glareshield (Pilot’s Side)
MASTER
WARNING/CAUTION
ROLL SPLRS
PLT CONT
HUD
DIM BRT
OFF
ROLL
SEL
PLT
ROLL
WARNING
CAUTION
FLIGHT INSTRUMENTS
Flight Crew Operating Manual REV 51, Aug 14, 2006
CSP 700−6
Volume 2
11−10−60
HEAD-UP DISPLAY SYSTEM (HUD) (IF INSTALLED) (CONT'D)
Combiner Unit Folding/Unfolding
The Combiner Unit folding/unfolding operation shall extend the combiner to operate and stow after
use. The image should be available within two seconds of deployement if the system is
powered-up (the power-up sequence is approximately one minute).
A handle, on the right side of the arm, folds or unfolds the Combiner Unit and locks it mechanically
when in the operational or stowed position.
To lock, turn the handle clockwise. To unlock, turn the handle counterclockwise.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：龐巴迪挑戰者手冊6(163)