曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

DEPLOYMENT BAG, AND STOWING
THE LINES
1. Lift the base of the folded canopy and slide the
reserve bag underneath. The grommets in the tongue
of the bag should be even with the bottom of the
stack. [Figure 5-95]
2. Make a second “S” fold to match figure 5-96.
3. Split the loose fabric at the top to form two “ears.”
[Figure 5-97]
Figure 5-92. Creating the “S” fold.
Figure 5-93. Wrap tail, two clamps.
Figure 5-94. Finish wrapping tail, four clamps.
Figure 5-95. Bag positioned under canopy.
Figure 5-96. Second “S” fold.
5-38
5-39
4. Gather the center cell material along the middle seam
until you reach the bottom. Roll the material under, but
do not cover the center cell. [Figure 5-98]
5. Hold down the center cell material and then shape the
molar folds. [Figure 5-99]
6. Fold the ends of the molar folds under to create the
bulk necessary to fill the top of the reserve bag.
[Figure 5-100]
7. When placing the canopy in the bag, allow the folded
canopy to stick out 2-3 inches at the mouth of the
bag to fill the corners of the reserve container.
[Figure 5-101]
8. Close bag and secure with the locking stows.
[Figure 5-102 on page 5-40]
9. Shape the bag. The shape of the bag should reflect
the desired shape of the reserve container.
10. Cover any exposed hook Velcro® to avoid contact with
the lines.
Figure 5-97. Split fabric and form “ears.”
Figure 5-98. Gather and roll center seam fabric.
Figure 5-99. Shape molar folds.
Figure 5-100. Fold molar ends under.
Figure 5-101. Place canopy in bag.
5-40
11. Stow the lines neatly leaving sufficient line between
the bag and riser ends. [Figure 5-103]
12. Thread the pull-up cord through the closing loop.
STEP 6. PLACING THE BAG INTO THE
CONTAINER AND CLOSING THE
CONTAINER
1. Place reserve risers into the pack tray. Spread the risers
with the rear riser to the outside to minimize the bulk
against the back pad. [Figure 5-104]
2. Place the reserve bag into the container and S-fold the
bridle in the center of the bag. [Figure 5-105]
3. Fold the top yoke portion of the bag over the bridle.
[Figure 5-106]
4. Secure in place with a clamp. [Figure 5-107]
5. Use the gun cleaning rod to thread the pull-up cord
through the pilot chute. [Figure 5-108]
Figure 5-102. Close bag and secure locking stows.
Figure 5-103. Stow lines.
Figure 5-104. Place risers in the pack tray and spread.
Figure 5-105. “S” fold the bridle on bag.
Figure 5-106. Fold the yoke over the bridle.
6. Center the base of the pilot chute on the center
grommet of the deployment bag.
7. Compress the pilot chute while stuffing fabric and
mesh between the spring coils.
8. Position the cap of the pilot chute with the arrow
facing toward the top or bottom of the container.
[Figure 5-109] Secure with a temporary pin.
9. If an AAD such as a CYPRES® is installed, route the
pull-up cord through the cutter first, then through the
right (#1) side flap grommet. [Figure 5-110]
Figure 5-107. Secure yoke/bridle with clamp.
Figure 5-108. Gun rod through the pilot chute.
Figure 5-109. Position pilot chute.
5-41
Figure 5-110. Route pull-up cord through cutter and right flap.
10. Next thread the left (#2) side flap grommet.
Simultaneously close the side flaps. [Figure 5-111]
Secure with a temporary pin.
11. Close the bottom flap (#3) and secure with a temporary
pin. [Figure 5-112]
Note: At this point, you should only be able to pull 1/4 –
1/2 inch of loop through the first three flaps. If you can
pull more, the loop is too long. Open container and
shorten loop.
12. Close flap #4 and insert ripcord pin. [Figure 5-113]
CAUTION: Place the closing plate on the bottom edge of
the inner top flap. This will protect the plastic stiffener if
you are kneeling on the pin protector flap.
The rigger should determine how tight the closing loop
is, and decide whether to perform a pull test.
WARNING: MAXIMUM ALLOWABLE PULL
FORCE ON THE RESERVE RIPCORD IS 22
POUNDS (10 KG)
13. Once you are satisfied that the pull force is less than
22 pounds (10 kg), seal the ripcord and log the pack
job.
14. Place the data card in the data card pocket. [Figure
5-114]
COUNT YOUR TOOLS!
Figure 5-111. Close right and left flaps simultaneously.
Figure 5-112. Close #3 bottom flap.
5-42
Figure 5-113. Close flap #4 and insert ripcord pin.
5-43
15. Complete the placard data on the orange warning
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：Parachute Rigger Handbook(55)