曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

equipment is essential for accurate testing and the type of
material must be known in order to test to the correct
strength. The testing equipment is shown in figure 5-12.
The full standard can be found in Appendix I of this handbook.
4. Along with the pull test, the AD also requires testing
the canopy mesh with a solution of Bromo Cresol Green
indicator to determine the presence of an acid condition.
The Bromo Cresol Green indicator is a dark blue liquid
in its standard state. It turns yellow when it contacts
acid—the stronger the acid, the brighter the yellow. If the
test is positive, the canopy will need to be treated to neutralize
the condition. The AD highlights the manufacturer’s
service bulletin as to how to comply with this test
and procedure.
5. If the canopy has a deployment device such as a diaper,
check that it is securely attached, particularly after use.
Check the grommets, line stow bands, elastics, or other
line stow devices. Pay particular attention to where the
stitching attaches to the canopy fabric. This area can be
particularly prone to damage during opening.
SUSPENSION LINES AND
CONNECTOR LINKS
1. The lines, their attachment points, and the associated
stitching should be checked for damage or missing
stitches. With the older sheath and core nylon lines such
as Ty-III found on military surplus canopies, the zigzag
stitching at the links are prone to raveling. The more
modern noncontinuous line canopies use Dacron® or
nylon braided lines. The common attachment at the links
for these lines uses the “finger-trap” method to secure the
lines to the link, with a bar tack securing the lines. Most
manufacturers now use a contrasting color thread for the
bar tack in order to make inspection easier. Make sure all
bar tacks are in place. Figure 5-13 shows both methods of
line attachment to the links.
2. There are three basic types of separable connector
links in common use today for round canopies. They are
the standard “L” bar type, MS-22002; the Navy speed link,
5-8
Figure 5-13. Connector link line attachment methods.
Figure 5-11. Round canopy gore inspection.
MS-22021; and the Quick link, commonly called the
Maillon Rapide® link, named after the French company
that first manufactured them. [Figure 5-14] The older military
surplus canopies are usually found with the two
types of MIL-SPEC connector links. Modern sport
canopies usually are found with the Rapide® links
because of their compatibility with the modern low bulk
suspension lines.
3. With the MIL-SPEC links, check the tightness of the
screws that hold the links together. With the speed links,
make sure the knurled side of the end cap is facing up and
the plates face outboard on the riser. The screw should
be checked for tightness at each repack.
4. If the canopy is equipped with Rapide® links, they
should be oriented on the riser with the barrel inboard and
to the bottom so it tightens upward. The link should be
tightened hand tight, then approximately one quarter turn
further. The actual force recommended for a number 5
link is approximately 30 foot-pounds. Most riggers do not
possess the force gauge to measure this, so they use the
quarter turn guide. After tightening the links, a “telltale”
should be applied to the barrel. [Figure 5-15] A telltale is
a marker, usually nail polish, that provides a breakable
seal to show if the barrel has moved. If the seal is broken,
the rigger knows the link may be loose. In doing a repack,
if the telltale is intact, the rigger should not loosen the
link and retighten it because continual tightening can strip
the threads, causing the link to fail.
HARNESS
1. Starting at the riser end, check the webbing for any
wear or damage and inspect the stitching at the riser ends.
If the canopy has steering lines and a guide ring on the
riser, make sure the ring is secure and the steering line is
attached to the steering toggle correctly. With a round
canopy, make sure the steering line has sufficient slack in
it when under tension. If the line is too tight, it can fail at
opening because of too much stretch.
2. Continue down the risers. If canopy releases are
installed, check their operation. With the Capewell cable
release, open the release and make sure there is no dirt or
sand in the mechanism. Also, check for wear, particularly
on the cable ring.
3. Check all of the harness webbing for wear both from
chafing, abrasion, and sunlight degradation. Pay particular
attention to the buffer and chafing strips where used
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：Parachute Rigger Handbook(44)