曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

SAVING" appears.
With the message "PARAMETER SAVED" the saving of the
new configuration to layout M (Modifiable) and into
the director is completed.
The MODIFICATION counter is incremented and displayed
(Here M = 019).
TMUCI2Y03-T02 LEVEL 3
EFFECTIVITY 23-73-00 Page 4
Apr 30/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL
MECHANICS / ELECTRICS & AVIONICS COURSE 23 COMMUNICATIONS
UF94200
EFFECTIVITY Page 350
ALL
TMUCI2Y03-P02 LEVEL 3
PTP CABIN RECONFIGURATION - CABIN ZONES
EFFECTIVITY 23-73-00 Page 5
Apr 30/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL
MECHANICS / ELECTRICS & AVIONICS COURSE 23 COMMUNICATIONS
UF94200
EFFECTIVITY Page 351
ALL
PTP CABIN RECONFIGURATION
NO SMOKING (NS) ZONES
The NS ZONES function gives the seatrow numbers of the
end of the NS ZONES for each cabin zone.
The NS zones are modified using the keyboard in the
same way as for the cabin zones.
NOTE : Entering a zero (0) deletes the NS zone in the
respective cabin zone.
If the layout of CABIN ZONES is changed, the NS ZONES
layout follows automatically.
The number of seatrows in each NS ZONE will remain
constant except if the CABIN ZONE is smaller than the
NS ZONE.
In case of symmetrical NS ZONES, the numbers will
appear only in the right hand positions of the menu
without left hand or right hand separations.
CLASS DIVIDER (DIV)
There can be passive class dividers (without sign
lamps) or active (with sign lamps).
The CLASS DIVIDER programming is used for BITE related
current sensing.
In case of cabin reprogramming, the class divider
should be moved manually.
TMUCI2Y03-T03 LEVEL 3
EFFECTIVITY 23-73-00 Page 6
Apr 30/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL
MECHANICS / ELECTRICS & AVIONICS COURSE 23 COMMUNICATIONS
UF94200
EFFECTIVITY Page 352
ALL
TMUCI2Y03-P03 LEVEL 3
PTP CABIN RECONFIGURATION - NO SMOKING - CLASS DIVIDER
EFFECTIVITY 23-73-00 Page 7
Apr 30/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL
MECHANICS / ELECTRICS & AVIONICS COURSE 23 COMMUNICATIONS
UF94200
EFFECTIVITY Page 353
ALL
PTP CABIN RECONFIGURATION
CAM LAYOUT SELECTION
The CABIN PROGRAMMING function is protected by an
access code.
Note that each code digit is marked by a * sign.
The CAM LAYOUT SELECTION function enables selection
of a new CAM layout. When activating the CIDS, the
last selected layout is loaded from the CAM into the
DIRECTOR memory.
The programmed layouts are marked with a "<" or ">"
sign. The number of the last selected layout flashes.
A new layout can be selected by pressing the
corresponding labelled key.
Then this number flashes and the layout is downloaded
into the director.
The CIDS system will then be completely updated.
The CAM shown here includes three fixed layouts 1 and
2 (a maximum of 3 fixed layouts can be programmed) and
the modifiable layout M.
If layout 1 or 2 are loaded and modified, they are
saved into layout M.
Layout M is now loaded.
If no CAM is available, the last downloaded LAYOUT is
maintained in the Director.
If no CAM is available and the last downloaded layout
is defective, the CIDS works with its own layout.
In these cases, the failure message "CIDS FAIL" appears
on the SYSTEM STATUS page.
TMUCI2Y03-T04 LEVEL 3
EFFECTIVITY 23-73-00 Page 8
Apr 30/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL
MECHANICS / ELECTRICS & AVIONICS COURSE 23 COMMUNICATIONS
UF94200
EFFECTIVITY Page 354
ALL
PTP CABIN RECONFIGURATION - CAM LAYOUT SELECTION
TMUCI2Y03-P04 LEVEL 3
EFFECTIVITY 23-73-00 Page 9
Apr 30/98
_A319/A320/A321 TECHNICAL TRAINING MANUAL
MECHANICS / ELECTRICS & AVIONICS COURSE 23 COMMUNICATIONS
UF94200
EFFECTIVITY Page 355
ALL
PTP CABIN RECONFIGURATION
STEPS TO MODIFY A SELECTED CABIN LAYOUT
- Load the desired layout 1 - 2 - 3 - M into
director (Example "2").
Select "ZONING" on the PTP.
- By programming steps, the layout data (cabin
zones, no-smoker zones, class divider) is
modified in the memory of the director (in the
RAM).
- After completing the programming, press "RET"
on the PTP, PTP displays "PARAMETER SAVING".
- Note: If "RET" is NOT pressed, the system will
operate with the modified data, until a
power interruption causes a restart of
the system. In this case the modified
data will be lost and the old layout "2"
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：ATA 23 COMMUNICATIONS(53)