曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

MACH
STATIC
SELECTOR
VALVE CLOSED
TRANSDUCER
SELECTOR
VALVE CLOSED
MACH
TRANSDUCER
PITOT
MACH
STATIC
SELECTOR
VALVE CLOSED
TRANSDUCER
STATIC
MACH
TRANS
2
MACH
TRANS
1
Standby
Instrument
Water
Drains
Vol. 1 12--30--7
REV 56, Jan 31/03
FLIGHT INSTRUMENTS
Air Data System
Flight Crew Operating Manual
CSP A--013
MASTER
Air Data Reference Control Panel
Figure 12---30---4
SEL
Used to alternately
select V1, VR or V2
to the edit field
when VSPDS is
selected.
PUSH / SET / OFF
Used to adjusts the selected speed
readout displayed on the edit field.
When pushed, the selected speed
readout is displayed.
When rotated, the selected speed
readout is adjusted.
When pushed again, the selected
speed readout is removed.
RA TEST
Used to initiate
radio altitude test.
HPA / IN
Used to alternately
select the barometric
pressure to be
displayed in
hectoPascals or
inches of mercury.
BARO
Used to adjust
barometric pressure.
When pushed, the
barometric pressure
is set to the standard
value of 29.92 inHg
or 1013 hPa.
When rotated, the
barometric pressure
setting is adjusted.
BARO
DH MDA
SPEED REFS
RATEST
HPA / IN
TGT VSPDS
SEL
Air Data Reference Panel
Pilot’s and Copilot’s
Side Panels
DH / MDA
Used to select decision height or
minimum descent altitude.
DH -- Decision height readout is
selected to be adjusted.
MDA -- Minimum descent altitude
readout is selected to be adjusted.
TGT / VSPDS
Used to select target or V speeds.
TGT -- VT speed is selected to
be displayed on the edit field.
VSPDS -- V1, VR and V2
speeds are selected to be
displayed on the edit field.
Alternate selection of V1, VR
and V2 is made using SEL.
PUSH / SET / OFF
Used to adjust selected altitude readout.
When pushed, the selected altitude readout
(DH or MDA) is displayed on the PFD.
When rotated, the selected altitude readout
is adjusted (DH in 1--ft. increments, MDA in
10--ft. increments).
When pushed again, the selected altitude
readout is removed.
REV 56, Jan 31/03
Vol. 1 12--30--8
FLIGHT INSTRUMENTS
Air Data System
Flight Crew Operating Manual MASTER
CSP A--013
Indicated Airspeed and Mach Indications <MST>
Figure 12---30---5
IAS Bug (magenta)
Indicates airspeed reference marker as set
by pilot using the speed knob on flight
control panel.
Indicated Airspeed Tape (white)
Moving tape that indicates current airspeed.
Tape range is 40 to 400 knots with a display
of 80 knots.
Marks at 5 knot increments.
Digits at 20 knot increments.
Trend Vector (magenta)
Indicates predicated airspeed
within next 10 seconds.
Indicated Airspeed Pointer (white)
Indicates current airspeed.
IAS /Mach Reference (magenta)
Indicates airspeed as selected
using the speed knob on flight
control panel.
Mach Readout (white)
Indicates Mach speed.
Displayed when Mach is
above 0.45 and is removed
when Mach is below 0.40.
Overspeed Cue (red/black checkerboard)
Assends from Vmo/Mmo to top of tape
window to indicate maximum speed allowable.
If speed is more than 3 kts greater than Vmo
or equivalent Mmo, overspeed clacker sounds.
Warning continues until speed is 3 kts below
Vmo/Mmo.
Low Speed Cue (red/black checkerboard)
Descends from stick shaker speed to edge of
tape window and acts as cue to impending
stall speed. Displayed 3 seconds after lift--off.
If AOA data fails, checkerboard stops at 100 kts.
and is replaced by a yellow line up to 120 kts.
CLACKER
TONE
Speed Reference Bugs (cyan)
Removed 7.5 seconds after speed
is exceeded (except target speed).
1 Takeoff decision speed (V1)
R Rotate airspeed (VR)
2 Take--off safety speed (V2)
T Target speed (VT)
Stall Speed Indicator (green line)
Indicates 1.25 times the computed stall speed.
Displayed in flight only.
2
120
180
160
140
T
R
1
Airspeed Indicator
Speed Reference (cyan)
Indicates reference speed as set
by pilot using the speed reference
knob on air data reference panel.
Airspeed Indicator
Primary Flight Display
Pilot’s and Copilot’s Instrument Panels
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：Bombardier_CRJ_00-Flight_Instruments(7)