曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

Baines， N.A.， Hajilouy-Benisi， A.， and Yeo， J.H.， 1994. ""The Pulse Flow Perform-ance and Modeling of Radial Inflow Turbines，'' IMechE， Paper No. a405j017.
Balje，O.E.， ""A Contribution the Problem of Designing Radial Turbo-machines，'' Trans.ASME， Vol.to74， p. 451 (1952).
Benisek，E.， 1998. ""Experimental and Analytical Investigation for the Flow Fieldof a TurbochargerTurbine，''IMechE， Paper No. 0554j027j98.
Benson，R.S.， ""A Review of Methods for Assessing Loss Coefficients in Radial GasTurbines，'' l7ter7atω27al J2ωr7al2曠 MeCha7ωCal SCωe7Ces， 12(1970)， pp. 905-932.
Karamanis， N.Martinez-Botas，R.F.，Su，C.C.， ""Mixed Flow Turbines: Inletand Exit flow under steady and pulsatingconditions，'' ASME 2000-GT-470.
Knoernschild，E.M.， ""The Radial Turbine for Low Specific Speeds and LowVelocityFactors，''J2ωr7al2曠 E7Aω7eerω7A曠2r P2wer， TransASME， SerialA，Vol.83， pp. 1-8 (1961).
Rodgers，C.， ""Efficiency and Performance Characteristics of RadialTurbines，''SAE Paper660754，October， 1966.
Shepherd，D.G.，Prω7Cωples2曠 Tωrb2 aChω7ery，NewYork， The MacmillanCompany， 1956.
Vavra，M.H.， ""RadialTurbines，'' Pt4.， AGARD-VKI Lecture Series on Flow inTurbines (Series No.6)，March， 1968.
Vincent，E.T.，""Theory and Design of Gas Turbines and JetEngines，'' NewYork，McGraw-Hill， 1950.
Wallace，F.J.， andPasha，S.G.A.，1972，DesωA7， C27strωCtω27 a7Z Testω7A2曠 a MωxeZ-Fl2w Tωrbω7e.
Winterbone，D.E.，Nikpour，B.， andAlexander，G.L.，1990， ""Measurement of the Performance of a Radial Inflow Turbine in Conditional Steady andUnsteadyFlow，''IMechE， Paper No. 0405j015.
9

Axial-Flow Turbines

Axial-flow turbines are the most widely employed turbines using a compres-sible fluid. Axial-flow turbines power most gas turbine units-except the smaller horsepower turbines-and they are more efficient than radial-inflow turbines in most operational ranges. The axial-flow turbine is also used in steamturbine design; however， there are some significant differences between the axial-flow turbine design for a gas turbine and the design for a steam turbine.
Steam turbine development preceded the gas turbine by many years.Thus， the axial-flow turbine used in gas turbines is an outgrowth of steam turbine technology. In recent years the trend in high turbine inlet temperatures in gas turbines has required various cooling schemes. These schemes are described in detail in this chapter with attention to both cooling effectiveness and aerodynamic effects. Steam turbine development has resulted in the design of two turbine types: the impulse turbine and the reaction turbine. The reaction turbine in most steam turbine designs has a 50% reaction level that has been found to be very efficient. This reaction level varies considerably in gas turbines and from hub to tip in a single-blade design.
Axial-flow turbines are now designed with a high work factor (ratio ofstage workto squareofblade speed)to obtainlowerfuelconsumptionandreducethe noise from the turbine. Lower fuel consumption and lower noise requires the designofhigherby-passratioengines.Ahighby-passratioenginerequiresmanyturbine stages to drive the high-flow， low-speed fan. Work is being conducted todevelop high-work， low-speed turbine stages that have high efficiencies.
Turbine Geometr.
The axial-flow turbine， like its counterpart the axial-flow compressor， hasflow， whichenters andleaves inthe axial direction. There aretwo types ofaxial
337
turbines: (1) impulse type， and (2) reaction type. The impulse turbine has its entire enthalpy drop in the nozzle; therefore it has a very high velocity entering the rotor. The reaction turbine divides the enthalpy drop in the nozzle and therotor. Figure 9-1 is a schematic of an axial-flow turbine， also depicting thedistribution of the pressure， temperature， and the absolute velocity.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：燃氣渦輪工程手冊 Gas Turbine Engineering Handbook 2(29)