(c)
After you clear the left ADIRS maintenance messages, if the observed fault continues to shows on the captain’s EFIS display, then continue.
(3)
Do this check of the ADIRU switching:
(a)
Make sure the right ADIRU is aligned and in the NAV mode.
(b)
Set the IRS switch on the P5 panel to the BOTH ON R position.
(c)
If the observed fault does not show on the captain’s EFIS display, then do these steps:
1) Replace the left ADIRU.
These are the tasks:
EFFECTIVITY SIL ALL 34-21 TASK 825
D633A103-SIL BOEING PROPRIETARY -Copyright # Unpublished Work -See title page for details Page 249 Oct 15/2008
737-600/700/800/900 FAULT ISOLATION MANUAL
Air Data Inertial Reference Unit Removal, AMM TASK 34-21-01-000-801, Air Data Inertial Reference Unit Installation, AMM TASK 34-21-01-400-801.
(d) If the observed fault shows on the captain’s EFIS display, then continue.
(4)
Replace the DEU 1. These are the Task: Display Electronic Unit Removal, AMM TASK 31-62-21-000-801 Display Electronic Unit Installation, AMM TASK 31-62-21-400-801
(a) If the installation test is satisfactory, then you corrected the fault.
(5)
Do a wiring check between the ADR to IR section of the ADIRU.
(a) For the left ADIRU, do a wiring check between terminal block TB523, to D3687B and D3687A:
TB523 D3687B
ZA21 -------------------pinK4
ZB21 -------------------pinK5
TB523 D3687A
ZA21 -------------------pinA9
ZB21 -------------------pinB9
(b)
If you find a problem with the wiring, then do these steps:
1) Repair the wiring.
2) Do
the
left
ADIRS
BITE
(34-21
TASK
801).
a) If there is a left ADIRS fault message that shows on the CDU, then go to the FIM task to clear that message. b) After you clear the left ADIRS maintenance messages, if the observed fault does not show on the captain’s EFIS display, then you corrected the fault. c) After you clear the left ADIRS maintenance messages, if the observed fault continues to shows on the captain’s EFIS display, then continue.
(c)
If you don’t find the problem with the wiring, then continue.
(6) Do this check of the wiring between the ADIRUs and the DEU 1:
(a)
Remove the left and right ADIRUs. To remove them, do this task: Air Data Inertial Reference Unit Removal, AMM TASK 34-21-01-000-801.
(b)
Remove the DEU 1. To remove it, do this task: Display Electronic Unit Removal, AMM TASK 31-62-21-000-801.
(c)
For the left ADIRU, do a wiring check between these pins of connectors D3687B and D3973A:
D3687B D3973A
pinG7 ------------------pinC2 pinG8 ------------------pinD2
(d) For the right ADIRU, do a wiring check between these pins of connectors D3693B and D3973D:
D3693B D3973D
pinC10 -----------------pinC2 pinC11 -----------------pinD2
EFFECTIVITY SIL ALL 34-21 TASK 825
D633A103-SIL BOEING PROPRIETARY -Copyright # Unpublished Work -See title page for details Page 250 Oct 15/2008
(e) If you find a problem with the wiring, then do these steps: 1) Repair the wiring. 2) Re-install the DEU 1. To install it, do this task: Display Electronic Unit Installation,
AMM TASK 31-62-21-400-801. 3) Re-install the left and right ADIRUs. To install them, do this task: Air Data Inertial Reference Unit Installation, AMM TASK 34-21-01-400-801. 4) If the observed fault does not show on the captain’s EFIS display, then you corrected the fault.
-------------------------END OF TASK ---------------------------
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-600/700/800/900 FAULT ISOLATION MANUAL 故障隔離手冊 導航(56)
