*
You must switch to the other Central Maintenance Computing Function to complete this data load. Do the following steps:
*
1. Select GO BACK
*
2. Select the OTHER FUNCTIONS menu and CENTRAL MAINTENACE SOURCE SWITCHING
45-10-00
Page 98.89 D633W101-BEJ Sep 05/2002
CMCS -DATA LOAD MESSAGE DIALOG BOXES -3
* 3. After you switch source, select DATA LOAD and start again.
The buttons are:
*
GO BACK
*
HELP.
Select GO BACK to remove the dialog box and return to the previous display.
Select HELP to show the help dialog box for the switch source CMCF dialog box dialog box. Help text for the dialog box must be in the CMCF AMI for HELP to show.
Data Loader Not Working Dialog Box
The data loader not working dialog box shows when the CMCF detects a fault with the data load gateway sub-function.
The message field shows:
*
The data loader finds and internal failure and cannot operate.
*
You may select CONTINUE to data load the AIMS CMCF/ Comm destination LRU. This may make the data loader serviceable.
*
NOTE: If you select CONTINUE, all functions of the connected Central Maintenance Computing Function will stop.
*
If a new load is necessary in the CPM/Comm, select CONTINUE.
The buttons are:
*
CONTINUE
*
HELP
*
GO BACK.
Select CONTINUE to start a data load of the CPM/Comm LRM.
Select HELP to show the help dialog box for the data loader not working dialog box. Help text for the dialog box must be in the CMCF AMI for HELP to show.
Select GO BACK to remove the dialog box and return to the previous display.
EFFECTIVITY BEJ ALL 45-10-00
Page 98.90
D633W101-BEJ Sep 05/2002
777 AIRCRAFT MAINTENANCE MANUAL
CMCS -DATA LOAD MESSAGE DIALOG BOXES -3
EFFECTIVITY BEJ ALL 45-10-00
Page 98.91
D633W101-BEJ Sep 05/2002
CMCS -HARD DRIVE MAIN MENU DIALOG BOX
General
The hard drive main menu dialog box gives access to functions that let you do these:
*
Add a new part number to the hard drive
*
Remove an existing part number from the hard drive
*
Show stored part numbers
*
Check a part number.
The software part numbers are on the maintenance access terminal (MAT) hard drive.
The hard drive main menu dialog box shows:
*
Exclusive selectors
*
Buttons.
Exclusive Selections
These are the four exclusive selections:
*
ADD A NEW PART NUMBER TO THE HARD DRIVE
*
REMOVE AN EXISTING PART NUMBER FROM THE HARD DRIVE
*
SHOW STORED PART NUMBERS
*
CHECK PART NUMBER.
Select ADD A NEW PART NUMBER TO THE HARD DRIVE to add LRU software part numbers to the hard drive.
Select REMOVE AN EXISTING PART NUMBER FROM THE HARD DRIVE to show the remove part number dialog box. Select the LRU software part number you want to remove from the remove part number dialog box.
Select SHOW STORED PART NUMBERS to show the show part numbers dialog box. The show part numbers dialog box shows:
*
Hard drive configuration name
*
Hard drive configuration index
*
Hard drive capacity
*
LRU software part numbers on the hard drive.
Select CHECK PART NUMBER to show the check part number dialog box. The check part number function checks that an LRU software part number is stored correctly on the hard disk. Select the LRU software part number you want to check from this dialog box.
Buttons
When you select an exclusive selection, the CONTINUE button is available. Select CONTINUE to go to one of the four hard drive software part number management functions.
Select HELP to show the help for this dialog box. Help text for the dialog box must be in the CMCF AMI for HELP to show.
Select GO BACK to remove the dialog box and return to the previous display.
EFFECTIVITY BEJ ALL 45-10-00
Page 98.92
D633W101-BEJ Sep 05/2002
777 AIRCRAFT MAINTENANCE MANUAL
CMCS -HARD DRIVE MAIN MENU DIALOG BOX
EFFECTIVITY BEJ ALL 45-10-00
Page 98.93
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：777 AMM 飛機維護手冊 中央維護 Central Maintenance(43)
