(b)  
Remove the DO-NOT-CLOSE tag and close the applicable circuit breaker below on the P11 panel: 1) 11H17, FLT CONT SHUTOFF TAIL LEFT 2) 11H18, FLT CONT SHUTOFF TAIL CTR 3) 11H28, FLT CONT SHUTOFF TAIL RIGHT

 S 222-078
 (10)
 Measure the rudder position.

 S 822-052

 (11)
 Do these steps if the rudder is more than 0.05 inch (1.3 mm) away from the datum position:

 (a)  
Do these steps to move the rudder to the right of its neutral position a small distance: 1) Loosen the jamnuts and adjust the input rod (for the

 powered PCA) until the rudder position is right of neutral a small distance.
 2)  Move the input levers for the disconnected PCAs across their neutral positions to remove all unwanted hydraulic pressure.
 (b)  Adjust the input rod for the powered PCA until the rudder is no more than 0.05 inch (1.3 mm) away from the datum position.
 NOTE: Always move the rudder from right to left during this
____ adjustment. Stop for 60 seconds to let the rudder position become stable.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-21-20
 ALL  ú ú 01 Page 217 ú Jan 28/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A

757
MAINTENANCE MANUAL

 (c)  
Tighten the control rod jamnuts.

 (d)  
Make sure the rudder is no more than 0.05 inch (1.3 mm) away from the datum position.

 S 862-053
 (12)
 Remove the power from the left, right, and center hydraulic systems (Ref 29-11-00).

 S 432-054

 (13)
 Connect the other two PCA input rods.

 S 092-055

 (14)
 Remove rig pin R3.

 S 412-056

 (15)
 Install the bullnose panel.

 S 862-057

 (16)
 Remove the DO-NOT-CLOSE tags and make sure these circuit breakers are closed on the P11 panel:

 (a)  
11H17, FLT CONT SHUTOFF TAIL LEFT

 (b)  
11H18, FLT CONT SHUTOFF TAIL CTR

 (c)  
11H28, FLT CONT SHUTOFF TAIL RIGHT

 S 862-058
 (17) Remove the DO-NOT-OPERATE tags and make sure the FLT CONTROL SHUTOFF switches L, C, and R are ON.
 S 862-060
 WARNING: KEEP PERSONS AND EQUIPMENT AWAY FROM ALL CONTROL SURFACES WHEN
_______ HYDRAULIC POWER IS SUPPLIED. AILERONS, ELEVATORS, RUDDER, FLAPS, SLATS, SPOILERS, AND STABILIZER ARE FULLY POWERED SURFACES. INJURY TO PERSONS OR DAMAGE TO EQUIPMENT CAN OCCUR WHEN HYDRAULIC POWER IS SUPPLIED.
 (18) Supply pressure to the left hydraulic system (Ref 29-11-00).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-21-20
 ALL  ú ú 01 Page 218 ú Jan 28/02
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
757
MAINTENANCE MANUAL

 S 222-084
 WARNING:_______ KEEP PERSONS AND EQUIPMENT AWAY FROM ALL CONTROL SURFACES WHEN
 HYDRAULIC POWER IS SUPPLIED.  AILERONS, ELEVATORS, RUDDER,
 FLAPS, SLATS, SPOILERS, AND STABILIZER ARE FULLY POWERED
 SURFACES.  INJURY TO PERSONS OR DAMAGE TO EQUIPMENT CAN OCCUR
 WHEN HYDRAULIC POWER IS SUPPLIED.

 (19)
 Turn the rudder trim switch to put the rudder in its neutral position and do this step:

 (a)  
Keep a record of the rudder position.

 NOTE: This is the datum position.
____
 S 862-061
 (20)
 Remove the power from the left hydraulic system (Ref 29-11-00).

 S 222-062

 (21)
 Supply pressure to the right hydraulic system (Ref 29-11-00) and do this check:

 (a)  
Make sure the rudder is not more than 0.10 inch (2.5 mm) away from the datum position.

 S 862-063
 (22)
 Remove the power from the right hydraulic system (Ref 29-11-00).

 S 222-064

 (23)
 Supply pressure to the center hydraulic system (Ref 29-11-00) and do this check:

 (a)  
Make sure the rudder is not more than 0.10 inch (2.5 mm) away from the datum position.
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：757 AMM 飛機(jī)維護(hù)手冊 飛行操縱 FLIGHT CONTROLS 2(85)