曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 (1)  Location Zone 572 Landing Gear Support Beam and Rear Spar to Trailing Edge, Left
 672  Landing Gear Support Beam and Rear Spar to Trailing Edge, Right
 E. Prepare to Adjust the Panel
 S 845-029
 WARNING: OPEN THE CIRCUIT BREAKERS TO PREVENT RETRACTION OF THE
_______ SPOILERS. THE SPOILERS WILL RETRACT AUTOMATICALLY IF YOU USE THE SPEED BRAKE LEVER TO LIFT THE SPOILERS AND IF HYDRAULIC SYSTEM NO. 1 AND 4 ARE NOT PRESSURIZED. INJURY TO PERSONS CAN OCCUR IF THE SPOILERS RETRACT.
 (1)  
Open the 7G6 SPEED BRAKE AUTO CONT circuit breaker on the P7 Overhead Circuit Breaker Panel.

 S 845-025

 (2)
Pressurize the hydraulic systems No. 1 and 4 (AMM 29-11-00/201).

 S 845-026

 (3)  
Put the speed brake control lever in the UP detent to lift the spoilers No. 5 through 8 above the inboard flap.

 S 845-027

 (4)  
Install the spoiler actuator locking tools or move the FLT CONTROL HYD POWER switches to SHUTOFF to prevent retraction of the spoilers.

 S 845-028

 (5)  
Release the pressure in the hydraulic systems No. 1 and 4 (AMM 29-11-00/201).

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 57-22-01
 ALL  ú ú 04 Page 502 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 57-22-01
 ALL  ú ú 01 Page 503 ú Feb 15/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

+0.010.50 INCH  0.50-INCH SPACER BLOCK, 
-0.01  PUT IMMEDIATELY AHEAD 
OF CREASE POINT  CREASE  STRAIGHTEDGE 
POINT  (144 INCHES)  FIXED TRAILING 
EDGE UPPER PANEL 

0.50-INCH SPACER BLOCK
LANDING GEAR BEAM
VERTICAL SEE THE TABLE FOR TIE ROD THE CLEARANCE (INCLUDES 0.50-INCH DIAGONAL THICKNESS OF THE
FWD
TIE ROD  SPACER BLOCKS)
NOTE: MEASURE THE DIMENSION AT A RIGHT ANGLE TO THE STRAIGHT EDGE.
TORQUE TUBE PANEL TIEDOWN, USING STRAIGHTEDGE
(RIB NO. 1)
A-A

SET TO 2.00-INCH FIXED SPACER
2.00 |0.01 INCH BLOCK PUT IMMEDIATELY
FORWARD OF THE CREASE POINT RIGGING BEAM CREASE (144 INCHES) POINT FIXED TRAILING
EDGE (FTE) UPPER PANEL
3.00-INCH ADJUSTING BLOCK
LANDING GEAR BEAM SEE THE TABLE FOR VERTICAL
THE CLEARANCE TIE ROD
(INCLUDES 2.00-INCH THICKNESS OF THE SPACER BLOCKS)DIAGONAL NOTE: MEASURE THE
TIE ROD
DIMENSION AT A RIGHT ANGLE TO THE STRAIGHT EDGE.
FWD
TORQUE TUBE PANEL TIEDOWN, USING RIGGING BEAM
(RIB NO. 1)
A-A

Fixed Trailing Edge Upper Panel Adjustment Figure 501 (Sheet 2)
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 57-22-01
 ALL  ú ú 01 Page 504 ú Feb 15/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
FORWARD EDGE ADJUSTING
OF PANEL

D-D
Fixed Trailing Edge Upper Panel Adjustment
Figure 501 (Sheet 3)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 57-22-01
 ALL  ú ú 01 Page 505 ú Feb 15/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL

CCREASE LINE
L
Fixed Trailing Edge Upper Panel Crease Line Location
Figure 502

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 機翼 WINGS(27)