(2)
Set dimension B as required for switch adjustment in table (Fig. 401).
(3)
Loosen but do not remove locknut securing switch arm to switch.
CAUTION: IF LOCKNUT IS NOT LOOSENED, DAMAGE TO WORM GEAR MECHANISM CAN OCCUR DURING ADJUSTMENT.
(4)
Loosen worm gear locking screw and turn worm gear on opposite side until switch actuates.
(5)
Tighten and lockwire worm gear locking screw, then tighten locknut.
(6)
Close LIGHTS and AURAL WARN circuit breaker on P6 panel.
F. Test stabilizer takeoff warning switch (Ref 31-26-00, Adjustment/Test).
563
Feb 15/77 BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details. 31-26-24 Page 401
H23757 G43319
Stabilizer Takeoff Warning Switch Installation 503
31-26-24 Figure 401 (Sheet 1) Nov 15/76
Page 402
BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.
514 Stabilizer Takeoff Warning Switch Installation
Jun 20/88 Figure 401 (Sheet 2) 31-26-24
Page 403
BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.
SPEED BRAKE TAKEOFF WARNING SWITCH - REMOVAL/INSTALLATION
1. General
A. The speed brake takeoff warning switch (S651) is installed on the upper left forward end of the control stand and is operated by an actuator on the speed brake lever.
2. Equipment and Materials
A. Ohmmeter
3. Remove Speed Brake Takeoff Warning Switch (S651) (Fig. 401)
A. Open LANDING GEAR LIGHTS circuit breaker on P6 panel.
B. Remove switch cover from control stand.
C. Disconnect electrical leads from switch.
D. Remove nuts and screws and remove switch (detail A).
E. Remove actuator from switch.
4. Install Speed Brake Takeoff Warning Switch (S651) (Fig. 401)
A. Place switch actuator on switch and install together on indicator plate (detail A). Do not tighten fasteners until switch adjustment is completed.
B. Adjust switch as follows:
(1)
Place speed brake lever in DOWN position.
(2)
Lower switch until clear of lever mounted switch actuator.
(3)
Connect ohmmeter across terminals C and NC of switch and check that switch is not actuated (continuity through switch).
(4)
Adjust switch upward against lever mounted switch actuator until switch actuates (no continuity through switch).
(5)
Tighten attachment fasteners.
(6)
Remove ohmmeter and connect electrical wiring to switch terminals.
C. Test speed brake takeoff warning switch (Ref 31-26-0, Adustment/Test).
563
Aug 15/77 BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details. 31-26-26 Page 401
H23764
Speed Brake Takeoff Warning Switch Installation 563
31-26-26 Figure 401 Feb 15/77
Page 402
BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.
CABIN ALTITUDE WARNING SWITCH - REMOVAL/INSTALLATION
1. General
A. The cabin altitude warning switch is located on the underside of the control cabin floor near the airplane centerline at station 192. Access is gained by removing access door 1103 from just forward of the nose wheel well.
2. Remove Cabin Altitude Warning Switch (Fig. 401)
A. Remove access door 1103.
B. Disconnect electrical plug at warning switch.
C. Remove switch mounting fasteners and remove switch.
3. Install Cabin Altitude Warning Switch (Fig. 401)
A. Position switch against floor panel and install fasteners.
B. Connect electrical connector to switch.
C. Install access door 1103.
D. Test Cabin Door Altitude Warning Switch
(1)
Provide electrical power.
(2)
Check that following circuit breakers are closed:
(a)
LEVER LATCH AND PRESS WARNING
(b)
AURAL WARN
(3)
Connect vacuum source to vent port of switch.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737 AMM 飛機維護手冊 通訊描述和操作(74)
