500  Cross-Shaft to Fuel Control Linkage 
May 01/99  Figure 505 (Sheet 2)  76-11-0 
Page 513 
BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details. 

Control System Rigging  516 
76-11-0  Figure 506 (Sheet 1)  Oct 20/85 
Page 514 
BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details. 

515  Control System Rigging 
Feb 15/79  Figure 506 (Sheet 2)  76-11-0 
Page 514A 
BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details. 

Control System Rigging  500 
76-11-0  Figure 506 (Sheet 3)  Aug 15/77 
Page 514B 
BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details. 

NOTE:  The following procedure makes initial detent setting. Refer to 78-32-01, Adjustment Test for final detent setting with engine operating.
(2)  
Adjust reverse thrust detent in control stand thrust lever as follows (Fig. 507):

(a)  
Remove thrust lever cover (1).

(b)  
Restrain nut (2) and torque cam lock bolt (3) to approximately 20 pound-inches (do not exceed 30 pound-inches).

(c)  
Rotate reverse thrust lever to engage roller assy (4) into the minimum power (No. 1) detent on the cam.

(d)  
Back out lock bolt until cam slips loose from tapered friction lock.

(e)  
Position the reverse thrust lever 87 +1/-l degree from the down (stowed) stop with roller remaining in No. 1 detent.

(f)  
Restrain nut (2) and torque cam lock bolt (3) to 25 +5/-O pound-inches.

(g)  
The clearance between the cam (5) and shaft (6) shall be 0.005 +0.035/-0.000 inches.

(h)  
Rotate reverse thrust lever from down (stowed) position to maximum travel stop

(135.5 degrees minimum from downstop) ten times. There shall be no cam slippage.

(i)  
The lever force, measured at the knob 90 degrees to centerline between knob and lever pivot, shall be 11.0 +8.0/-0.0 pounds as the roller moves through the No. 2 detent toward maximum reverse thrust.

(j)  
Replace or delete spacer (7) as required to adjust the lever force through the No. 2 detent. Not more than one spacer may be installed.

NOTE:  Spacers are available in thicknesses from 0.03 to 0.12 inch in 0.03-inch increments. Force adjustment range is approximately 5 pounds from no spacer to thickest spacer.

(k)  
Release spring force from spacer by restraining guide in depressed position using hole provided and moving reverse thrust lever to stowed position.

(l)  
Replace thrust lever cover (1).

(3)  
Install reverse thrust follow-up push-pull cable in thrust reverser crank arm (Ref 78-34-32, Thrust Reverser Push-Pull Cable Installation).

(4)  
Close reverse thrust isolation valve circuit breakers C276 and C277.

(5)  
Remove reverse thrust isolation valve ground lock assembly.

(6)  
Perform reverse thrust control system test procedure.

584 
May 15/80  BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.  76-11-0 Page 514C 

584 
76-11-0 Page 514D  BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.  Oct 20/85 

C.  Start Control System Adjustment
(1)  
Equipment and Materials

(a)  
Tensiometer - 0- to 125-pound capacity

(b)  
Rig Pin Kit - F70207-3, -52 or -61 1) Type 3 - F70207-23, 0.248 +0.000/-0.002-inch diameter rod

(2)  
Prepare engine start control system for adjustment/test.

(a)  
Remove side removable cowl panels (Ref Chapter 71, Removable Cowl Panels).

(b)  
Remove following access door in wing leading edge above wing-to-engine fairing (Ref Chapter 12, Access Doors and Panels): 1) No. 6301 in left wing. 2) No. 6401 in right wing.

(c)  
Gain access to control cable turnbuckles in wing leading edge by extending leading edge flaps as described in par. 2.A.(2)(e).

(3)  
Adjust start control cables.

(a)  
Disconnect engine start push-pull cable at left start crank on engine cross-shaft (Fig. 504).

(b)  
Check that start lever is in the cutoff detent.

(c)  
Perform steps (3)(d) and on for new cables and steps (3)(e) and on for rerigged cables.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737 AMM 飛機維護手冊 發動機控制 ENGINE CONTROLS(9)