520 Forward Entry Door Guide Arm Roller Installation
May 15/78 Figure 401 52-11-21
Page 403
BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.
H. Open door to position where latch lever shaft (21), link (9), door open stowing latch lever (20), and retaining screw (8), nut (18) and washers (19) may be installed.
I. Swing radius links (4) and (16) round on to guide arm, line up holes and install pin (26), washers (13) and (23) and retainer ring (25).
CAUTION: DO NOT INSTALL A USED RETAINER RING (25). INSTALL A NEW RETAINER RING (25) ONLY. IF THE RETAINER RING COMES OFF THE PIN (26) THE DOOR MAY NOT OPEN.
506
52-11-21 Page 404 BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details. Jun 20/89
FORWARD ENTRY DOOR LINING AND INSULATION - REMOVAL/INSTALLATION
1. Equipment and Materials
A. Spanner Wrench - Assist Handle, Main Entry Door - F70336-1.
2. Remove Forward Entry Door Lining and Insulation (Fig. 401)
CAUTION: USE SPECIAL CARE IN HANDLING THE PARTS OF THIS INSTALLATION. SURFACES VISIBLE TO CABIN INTERIOR MUST BE FREE OF SCRATCHES, MARKS AND DENTS.
A. Operate door handle fully, bringing door into cocked position.
B. Remove upper panel (1) from door (3).
(1)
Remove attach nuts (2) at forward and aft corners of upper edge of panel (1). Loosen remaining nuts along top edge of panel.
(2)
Loosen panel fastener studs (11, detail A) one-quarter turn on forward and aft edges of panel.
(3)
Pull upper edge of panel (1) inboard and up to release panel from trim strip (4). Remove upper panel from door.
C. Remove escape slide assembly (8) from door (3) (Ref Chapter 25, Escape Slide Assembly [Door-Mounted].)
D. Remove lower panel (6) from door (3).
(1)
With door in cocked position, remove door interior handle (9, detail B).
(a)
Remove insert (17) from spring clips (18), taking care not to mar polished surface of handle.
(b)
Remove three bolts (16), washers, insert support, and remove the handle and shims
(14) from the door.
(2)
Remove four screws (15) attaching lower panel (6) to lining retainer (13).
(3)
Remove assist handle (5, detail C).
(a)
Rotate nut (20) using wrench (23), and remove assist handle.
(b)
Remove bolts (22), washers, and collars (21) within nuts and lift off nuts and outer collars (19).
(4)
Remove attach nuts (7) at forward and aft corners of lower edge of panel (6). Loosen remaining nuts along bottom edge of panel.
(5)
Loosen panel fastener studs (12, detail A) one-quarter turn on forward and aft edges of panel (6).
(6)
Pull lower edge of panel (6) inboard and down to release panel from trim strip (4). Remove panel from door.
500
Jan 20/82 BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details. 52-11-31 Page 401
Forward Entry Door Lining and Insulation 506
52-11-31 Figure 401 (Sheet 1) May 15/69
Page 402
BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.
532 Forward Entry Door Lining and Insulation Installation
Jun 20/85 Figure 401 (Sheet 2) 52-11-31
Page 403
BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.
NOTE: Inboard window pane assembly (10) will be removed with lower panel (6). For removal of window from door, refer to Chapter 56, Door-Mounted Windows.
E. Remove retaining nuts and remove inboard window pane assembly (10) from the panel (6).
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737 AMM 飛機(jī)維護(hù)手冊 艙門 DOORS(33)
