Navigation Lights Relamping 543
33-43-11 Figure 201 (Sheet 1) Feb 15/73
Page 202
BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.
543 Navigation Lights Relamping
Feb 15/73 Figure 201 (Sheet 2) 33-43-11
Page 203
BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.
4. Relamp White Navigation Tail Light (Fig. 201)
A. Remove three lens retaining screws.
B. Remove collar and lens.
C. Replace lamp.
D. Clean lens with a clean, soft, dry cloth.
E. Slip collar over lens and install with three screws.
F. Test navigation light per par. 5.
5. Test Navigation Lights
A. Provide electrical power.
B. Check that POSITION light circuit breakers on P18-3 circuit breaker panel are closed.
C. Set POSITION light switch on overhead panel P5. Observe navigation lights come on.
D. Return POSITION light switch to OFF.
E. Remove electrical power if no longer required.
501
33-43-11 Page 204 BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details. Jun 20/85
WING FIXED NAVIGATION LIGHT - REMOVAL/INSTALLATION
1. General
A. The following procedures provide instructions for replacing the colored and white navigation lights. Refer to 33-45-11 for maintenance practices on wingtip strobe lights, as applicable.
B. The window covering the colored navigation lights is carefully sealed against possible entry of fuel vapors and should not be removed. A panel on the underside of the wingtip provides access to the lights.
2. References
A. Standard Wiring Practices Manual (SWPM), 20-30-00
3. Remove Colored Navigation Lights (Fig. 401)
A. Remove access panel on underside of wingtip.
B. Remove electrical wiring from terminals.
C. Remove lockwiring from lens retaining screw.
D. Remove three mounting screws and remove light.
4. Install Colored Navigation Lights (Fig. 401)
A. Position lens and lens retainer assembly in bracket.
NOTE: Install with indexing pin hole down on left wing or with indexing pin hole up on right wing.
B. Install lens retaining screw and lockwire.
C. Install lamp in socket with silvered portion facing aft and tighten pressure nut finger-tight.
D. Align indexing pin with hole in lens; place light assembly base in position and install with two captive screws.
E. Connect electrical wiring to terminals.
F. Seal the electrical terminals for a fuel vapor area (SWPM 20-30-00).
WARNING: MAKE SURE YOU SEAL EACH BARE ELECTRICAL CONNECTION TO PREVENT AN EXPLOSION OF THE FUEL FUMES. AN EXPLOSION CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
541
Feb 01/95 BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details. 33-43-11 Page 401
Navigation Lights Installation 543
33-43-11 Figure 401 (Sheet 1) Feb 15/73
Page 402
BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.
543 Navigation Lights Installation
Feb 15/73 Figure 401 (Sheet 2) 33-43-11
Page 403
BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.
G. Install access panel.
H. Test navigation lights.
(1)
Apply electrical power.
(2)
Check that STEADY circuit breaker on P18-3 panel is closed.
(3)
Place POSITION light switch on overhead panel P5 to STEADY. Observe navigation light comes on.
(4)
Return POSITION light switch to OFF.
(5)
Remove electrical power if no longer required.
5. Remove White Navigation (Tail) Light (Fig. 401)
A. Remove three screws retaining light assembly in tube.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737 AMM 飛機維護手冊 燈 LIGHTS(52)
