4.  Repair of Main Landing Gear Axle Sleeves
A.  Wear Limits
(1)  
Check diameters of inboard and outboard bearing boss for wear as shown on figure 802.

(2)  
If wear on bearing boss exceeds specified wear Limits and clearance between bearing and boss exceeds 0.0006 inch, axle sleeves must be removed for replacement or repaired per OHM 32-11-11.

(3)  
If wear on bearing boss exceeds specified wear Limits, but clearance between bearing and boss does not exceed 0.0006 inch, axle sleeves may continue in service for 65 hours flying time before being removed for replacement or repair per OHM 32-11-11.

B.  Local Damage Between Bearing Surfaces
(1)  Remove sharp edges and blend damage to a 0.50-inch radius and use a smooth finish. Rework must not reduce wall thickness be more than 0.025-inch for P/N 65C33516-1,  65-46147-1 and 65-46147-2 or 0.012-inch for P/N 65-46147-3.
C.  Damage to Bearing Surfaces
(1)  
Remove sharp edges and blend damage to a 0.05-inch radius and a smooth finish. Rework must not reduce wall thickness by more than 0.025-inch or exceed 30% of the total bearing area of any 90 degree segment.

(2)  
If damage exists at the anti-rotation bolt hole, either replace sleeve or contact Boeing for evaluation of possible repair.

500  Allowable Wear Limits of Installed Axle Sleeves 
Oct 20/92  Figure 802 BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.  32-11-111 Page 803 

MAIN GEAR ELECTRICAL HARNESS - REMOVAL/INSTALLATION
1.  Remove Electrical Harness (Fig. 401)
A.  On airplanes installed with gravel protection shield, remove clamp from shield. Remove shield.
B.  Remove antiskid transducer (32-42-11, Removal/Installation) to gain access to connectors.
C.  Pull electric connectors out of axle and disconnect wires.
D.  Remove fittings (l, 2), washer(s) (4) and expandable fitting (3) from hole in axle (Detail C, Fig. 401).
NOTE:  Note number of washers to facilitate reassembly.
E.  Remove hose clamps.
NOTE:  Do not remove ratchet clamps and tape from hose unless replacement is necessary.
F.  Remove hose assembly.
2.  Install Electrical Harness (Fig. 401)
A.  Position hose assembly on main gear and secure with clamps. Take care that markers V-1 thru V-4 on hose are located correctly in respect to clamp as shown in Fig. 401.
NOTE:  Special care must be exercised during installation of this hose to assure a minimum clearance of 1.00 inch with adjacent control cables.
B.  If tape needs replacement, wrap two layers of new tape around hose per BAC5801 and to dimensions shown (Detail B, Fig. 401). Overlap wraps by approximately 0.25 inch. Secure ends of taped areas with ratchet clamps. Keep the ratchet portion turned away from gear structure to prevent galling.
C.  Slide washer or washers (4) on expandable fitting (3). Position expandable fitting in bore of main gear axle. Insert fitting (2) in expandable fitting with tapered end showing forward. Hold expandable fitting stationary. Screw fitting (l) into expandable fitting and tighten. Check for snug fit of expandable fitting in axle bore. If still loose, add washers.
D.  Feed pigtail ends of hose assembly through fittings (l and 2) and through expandable fitting (3) into bore of axle. Pull pigtails out of axle ends and crimp on connector (Detail A, Fig. 401) (Ref Chapter 20). Use sleeves if required to make clamp fit tight.
E.  Screw elbow of hose assembly on fitting (l), and tighten. Lockwire fitting to expandable fitting.
F.  Reinstall antiskid transducer (Ref 32-42-11, Removal/Installation).
G.  On airplane installed with gravel protection shield, install shield. Install clamp on shield.
501 
Oct 20/84  BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.  32-11-121 Page 401 

Main Gear Electrical Harness Installation  513 
32-11-121 Page 402  Figure 401 (Sheet 1) BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.  Nov 15/76 

513  Main Gear Electrical Harness Installation 
May 15/78  Figure 401 (Sheet 2) BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.  32-11-121 Page 403 

Main Gear Electrical Harness Installation  501 
32-11-121 Page 404  Figure 401 (Sheet 3) BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.  Nov 15/76 
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737 AMM 飛機維護手冊 起落架 LANDING GEAR(50)