4) Verify valve No. 6 is open. a) With B flight control switch ON, move control column full travel and check that column force is approximately 25 pounds. 
NOTE:  If valve is closed, column force will be approximately 60 pounds. This can be verified by positioning B flight control switch to OFF and comparing forces.
5) Verify valve No. 5 is open. a) With B flight control switch ON, move rudder pedals full travel and check that pedal force is approximately 60 pounds.
NOTE:  If valve is closed, pedal force will be approximately 160 pounds. This can be verified by positioning B flight control switch to OFF and comparing forces.
6) Verify valve No. 1 is open. a) Position A flight control switch to ON and check that FEEL DIFF PRESS light goes out. 7) Verify valve No. 3 is open. a) With B flight control switch OFF and A flight control switch ON, repeat step 4) a). 8) Verify valve No. 2 is open. a) With B flight control switch OFF and A flight control switch ON, repeat step 5)a).
(c)  
Remove hydraulic power (Ref 29-12-0, Hydraulic System B - Maintenance Practices).

(d)  
Open any hydraulic isolation shutoff valve found closed during test. Install locking bar over open valves and secure with bolt and nut.

(e)  
Open landing gear shutoff valves. Install guard bracket to secure valves in open position.

(f)  
Close standby pump NORMAL (No. 1 GEN BUS) and ALTERNATE (No. 2 GEN BUS) circuit breakers on the P6 panel.

(g)  
Position alternate arm switch to off.

(h)  
Position flight control switches A and B and spoiler switches on.

(i)  
Remove electrical power from airplane.

500 
29-00 Page 622  BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.  Jun 20/85 

502  Internal Leakage Test Data Sheet 
Aug 01/94  (Sheet 1)  29-00 
Page 622A 
BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details. 

502  Internal Leakage Test Data Sheet 
Aug 01/94  (Sheet 2)  29-00 
Page 622B 
BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details. 

502  Internal Leakage Test Data Sheet 
Aug 01/94  (Sheet 3)  29-00 
Page 622C 
BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details. 

502  Internal Leakage Test Data Sheet 
Oct 20/85  (Sheet 4)  29-00 
Page 622D 
BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details. 

A/P No. ____________ Pump Mfr. __________ Ser. No. ____________ Date _______________  Recorded  Amp  Flow (cc/min) (Fig. 604)  Max Flow Limit (cc/min) 
Pump Used:  No. 1 or No. 2  Amps  Change  Cumulative  Increment 
as. Establish new basic reference [Step 1.C.(6)(bh)]  _________  _______  ________  _____ 
 
at. Left main gear and lock leakage [Step 1.C.(6)(bi)]  _________  _______  ________  at-as ____  300 
au. Right main gear and lock leakage [Step 1.C.(6)(bj)]  _________  _______  ________  au-at ____  300 
av. No. 1 thrust reverser stowed leakage [Step 1.C.(6)(bk)]  _________  _______  ________  av-au ___  300 
aw. No. 2 thrust reverser stowed leakage [Step 1.C.(6)(bl)]  _________  _______  ________  aw-av ___  300 

500  Internal Leakage Test Data Sheet 
Aug 01/94  (Sheet 5)  29-00 
Page 622E 
BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details. 

D.  Standby Hydraulic System Internal Leakage Check
(1)  General
(a)  
The following procedure provides instructions for performing an internal leakage check of the standby hydraulic system to determine the condition of the system based on the degree of internal leakage. By comparing measured leakage to recommended in-service leakage limits, a determination of the system condition can be made.

(b)  
Leakage flows are determined by measuring changes in the flow rates during different operating conditions while hydraulic power is applied. Three methods for measuring the flow rates are available: the ammeter method, the flowmeter method and the amp-clamp and multimeter method. 1) The ammeter method uses an ammeter connected in series with one phase of

the standby pump. The leakage rates are determined by measuring the current and current changes of the pump. These current changes are then related to an amperage versus flow rate chart (Fig. 608).
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737 AMM 飛機維護手冊 液壓 HYDRAULIC POWER(19)