(d)
Do a check of the wear surfaces of the parts with a micrometer or vernier caliper as applicable (Fig. 601).
(e)
Compare the dimensions measured with the permitted dimensions shown in Fig. 601.
(f)
Repair or replace the parts that are not in the tolerance specified in Fig. 601.
(g)
Connect the ballnut to the gimbal.
3. Flap Drivescrew Backlash Test (Fig. 602)
A. Special Tools and Equipment
(1) C27030-33 – Flap Drivescrew Backlash Tool
B. References
(1)
AMM 24-22-0/201, Manual Control
(2)
AMM 27-51-0/201, Trailing Edge Flaps
(3)
AMM 27-51-141/401, Inboard Flap Track Fairing
(4)
AMM 27-51-121/401, Outboard Flap Track Fairings
(5)
AMM 27-51-73/401, Flap Drivescrew
500
27-51-73 Page 602 BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details. May 01/99
H97031 H97033 H97037 H97034
500 Flap Drivescrew Wear Limits
May 01/99 Figure 601 (Sheet 1) 27-51-73
Page 603
BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.
Flap Drivescrew Wear Limits 500
27-51-73 Figure 601 (Sheet 2) May 01/99
Page 604
BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.
500 Flap Drivescrew Wear Limits
May 01/99 Figure 601 (Sheet 3) 27-51-73
Page 605
BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.
Flap Drivescrew Backlash Tool, C27030-33 500
27-51-73 Figure 602 May 01/99
Page 606
BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.
C. Access
(1) Location Zone
307, 407 Wing Trailing Edge Outboard Flap and Spoiler
309, 409 Wing Trailing Edge Inboard Flap and Spoiler
D. Prepare for the Flap Drivescrew Backlash Check
(1)
Supply electrical power (AMM 24-22-0/201).
(2)
Do the applicable steps that follow to get access to the flap drivescrew:
(a)
Remove the center fairing (AMM 27-51-121/401) to get access for the positions that follow: 1) Position No. 1 2) Position No. 2 3) Position No. 7 4) Position No. 8
(b)
Remove the tailcone assembly (the aft part of the fairing for the outboard track of the inboard flap) to get access to the positions that follow: 1) Position No. 3 2) Position No. 6
(c)
Remove the fairing for the inboard track of the inboard flap to access for the positions that follow (AMM 27-51-141/401): 1) Position No. 4 2) Position No. 5
(3)
Supply hydraulic power (AMM 27-51-0/201).
(4)
Do the steps that follow to put the flaps in the correct position to do the check of the flap drivescrew backlash:
NOTE: You must have approximately 4 inches of the drivescrew aft of the ballnut to let you install the lever and clamp tool (these are part of the drivescrew backlash test tool kit).
(a)
To do the check at the No. 1, No. 2, No. 7 or No. 8 position, do the steps that follow to put the flaps at the 25 unit position: 1) Move the flap handle on the control stand to the 25 unit position. 2) Make sure the flaps move to the 25 unit position.
(b)
To complete a check at the No. 3 or No. 6 position, do the steps that follow to put the flaps to the 30 unit position: 1) Move the flap handle on the control stand to the 30 unit position. 2) Make sure that the flaps move to the 30 unit position.
(c)
To complete the check at the No. 4 or No. 5 position, do the steps that follow to put the flaps to the 25 or the 30 unit position: 1) Move the flap handle on the control stand to the 25 or the 30 unit position. 2) Make sure that the flaps move to the specified position.
(5)
Remove the hydraulic power (AMM 27-51-0/201).
(6)
Do the locking procedure for the drive system of the trailing edge flaps
(AMM 27-51-0/201).
500
May 01/99 BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details. 27-51-73 Page 607
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 3(33)
