(2)
Put all the refuel valve switches to the CLOSED position.
(3)
Make sure the onboard fuel load is in a valid pre-flight fuel distribution.
(a)
Tanks No. 1 and 2 must have equal quantities of fuel.
(b)
In general, do not put fuel in the center tank if the tanks No. 1 and 2 are not full.
(c)
AIRPLANES WITH AN AUXILIARY TANK; Make sure all other tanks are full before you put fuel in the auxiliary fuel tank.
(4)
Transfer fuel to balance the fuel load if necessary (AMM 28-23-0/201).
(5)
Wait one minute to let the fuel quantities stabilize.
(6)
Record the actual fuel quantities from the fueling quantity indicators.
(7)
Record the actual fuel quantity from the fuel vehicle flow meter.
(8)
Do the discrepancy check and make sure it is within limits.
NOTE: Per the operator's requirement.
(9)
Complete the Fuel Sheet.
(10)
Complete the Delivery Receipt if necessary.
(11)
Give a copy of the forms to the airline representative or flight crew.
H. Put the Airplane Back to Its Usual Condition
(1)
Make sure all the P15 panel valve switches are in the CLOSED position.
(2)
Put the test gages switch to the OFF position (if necessary).
(3)
Disconnect the refuel nozzle from the airplane.
(4)
Remove the refuel nozzle bonding cable (if installed).
(5)
Make sure the fueling receptacle adapter is not damaged.
(6)
Install the fueling receptacle cap.
(7)
Close and security latch the fueling station access door.
(8)
AIRPLANES WITH AN AUXILIARY TANK; Put the defueling valve handle in the CLOSED position and close the defueling valve access door.
(9)
Disconnect the bonding/grounding cables (AMM 20-41-11/201).
(10)
Do the operator supplied procedures to remove the fuel vehicle.
(11)
Do this task to remove the lock from the extended leading edge flaps and slats: Leading Edge Flap and Slat Lock Application (AMM 27-81-0/201).
WARNING: DO THE PROCEDURE IN AMM 27-81-0/201 TO REMOVE THE LOCKS ON ALL EXTENDED LEADING EDGE FLAPS AND SLATS. THE FLAPS AND SLATS MOVE QUICKLY AND CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
500
May 01/03 BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details. 12-11-02 Page 303
N96317 N96504
Pressure Refueling 500
12-11-02 Figure 301 (Sheet 1) May 01/03
Page 304
BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.
500 Pressure Refueling
May 01/03 Figure 301 (Sheet 2) 12-11-02
Page 305
BOEING PROPRIETARY - Copyright . - Unpublished Work - See title page for details.
OVERWING REFUELING - SERVICING
1. General
A. This procedure contains instructions, precautions and limits for overwing refueling.
B. Overwing refueling lets the operator add fuel to the main fuel tanks. Fuel is added through the fill ports found on top of the wings. Fuel is transferred to the center tank or auxiliary tank (if installed) as necessary.
C. Overwing refueling of the No. 1 and 2 tanks can be done if the pressure refuel equipment, or electrical power is not available. With electrical power available, the fuel quantity can be monitored from the flight compartment or the fueling panel (P15). With no electrical power available, the fuel quantity can be monitored with fuel measuring sticks.
D. If operation of boost pumps or fueling quantity indicators is necessary during overwing refueling, external power can be used for pump or indicator operation.
2. Overwing Refueling (Fig. 301)
A. Prepare the Airplane for an Overwing Refuel Operation
(1)
Read and obey the precautions in this task: Precautions and Limits for Fuel Servicing (AMM 12-11-01/301).
WARNING: OBEY ALL THE FUEL SERVICING PRECAUTIONS IN AMM 12-11-01/301. FAILURE TO OBEY THE PRECAUTIONS CAN CAUSE SERIOUS INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
(2)
Supply electrical power (AMM 24-22-0/201).
(3)
Do not operate the APU during a overwing refuel operation.
(4)
Make sure the airplane is in a 1 ±0.25° nose down and a 0 ±0.25° roll attitude.
(5)
Sump the water from the fuel tanks before you refuel the airplane (AMM 12-11-05/301).
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737 AMM 飛機維護手冊 SERVICING(10)
