F 『
E C F M E
E E
E 56 E
E E
R (d) Do a continuity and insulation check of this wiring.
R 1_ if damage is found:
R - replace or repair the above harness.
R 2_ if nothing is found:
R - continue the troubleshooting as follows.
R (e) Do a pin retention check on connectors sockets.
R 1_ if damage is found:
R - replace or repair the above harness.
R 2_ if nothing is found:
R - continue the troubleshooting as follows.
R (f) Do a check for absence of corrosion or contamination. Pay
R particular attention to engine to pylon connector.
R 1_ If damage is found:
R - repair the A/C electrical wiring or replace the J3 harness
R (Ref. AMM TASK 71-51-43-000-046) and (Ref. AMM TASK 71-51-
43-400-046).
R (4) If the test gives the maintenance message TLA SNSR, J4, ECU
R (confirmed on channel B):
R - Disconnect the J4 harness from the ECU (4000KS) receptacle and
R visually examine the ECU receptacle and the J4 harness connector
R for damaged pins or contamination (Ref. AMM TASK 73-21-50-210-002).
R (a) If damage on a connector is found:
R - replace or repair as required.
R (b) If nothing is found:
R - do an electrical resistance test through the J4 harness
R between:
R . pins 17 and 30 (30 to 40 ohms)
R . pins 5 and 15 (15 to 25 ohms)
R . pins 29 and 28 (15 to 25 ohms)
R . pins 17 and 16 (> 10 megohms)
R . pins 5 and 16 (> 10 megohms)
R . pins 29 and 16 (> 10 megohms)
R . pin 17 and the ground (> 10 megohms)
R . pin 5 and the ground (> 10 megohms)
R . pin 29 and the ground (> 10 megohms).
R 1_ If the resistance values are in the specified limits:
R - replace the ECU (4000KS) (Ref. AMM TASK 73-21-60-000-001)
R and (Ref. AMM TASK 73-21-60-400-001).
F 『
∞∞76-11-00∞∞∞∞∞∞∞∞∞∞Page 210
EEFF : ALL E
E E Feb 01/99
E E
ECES E
F 『
E C F M E
E E
E 56 E
E E
2 If the resistance values are out of the specified limits:
_ R - disconnect the connector DD at the throttle control unit R (8KS2) and do the resistance check at the throttle control
unit connector between:
. pins A, B (30 to 40 ohms)
. pins C, D (15 to 25 ohms)
. pins E, F (15 to 25 ohms)
.pin A and the ground (> 10 megohms)
.pin B and the ground (> 10 megohms)
.pin C and the ground (> 10 megohms)
a If the resistance values are out of the specified limits:
_
- replace the CTL UNIT-THROTTLE, ENG2 (8KS2) (Ref. AMM TASK 76-11-19-000-042) and (Ref. AMM TASK 76-11-19-400-042).
b If the resistance values are in the specified limits:
_
- continue the troubleshooting as follows.
(c) Do a check of the electrical wiring between the throttle control unit (8KS2) and the ECU (4000KS) (Ref. ASM 73-25/12).
1 if damage is found:
_
- replace or repair the above harness.
2 if nothing is found:
_
- continue the troubleshooting as follows.
(d) Do a continuity and insulation check of this wiring
1 if damage is found:
_
- replace or repair the above harness.
2 if nothing is found:
_
- continue the troubleshooting as follows.
(e) Do a pin retention check on connectors sockets.
1 if damage is found:
_
- replace or repair the above harness.
2 if nothing is found:
_
- continue the troubleshooting as follows.
(f) Do a check for absence of corrosion or contamination. Pay particular attention to engine to pylon connector.
1 If damage is found:
_
- repair the A/C electrical wiring or replace the J4 harness (Ref. AMM TASK 71-51-43-000-047) and (Ref. AMM TASK 71-51-43-400-047) as required
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 發(fā)動機控制(6)
