(1TX1)
ASM 46-21/05
3. Fault Confirmation
__________________
A. Test
(1) Do the BITE test of the ATIMS (Ref. AMM TASK 46-21-00-740-001).
4. Fault Isolation
_______________
A. If the test gives the maintenance message :
FMGC1(1CA1) BUS FM ACARS/ATSU1(1TX1):
- replace the FMGC-1 (1CA1) (Ref. AMM TASK 22-83-34-000-001) and (Ref. AMM TASK 22-83-34-400-001).
(1) If the fault continues:
- replace the ATSU (1TX1) (Ref. AMM TASK 46-21-34-000-001) and (Ref. AMM TASK 46-21-34-400-001).
(a) If the fault continues:
- remove the FMGC 1 and the ATSU
- do a check and repair the wiring of the PRINTER ACARS & ATSU DATA BUS: between pins AB/12F,12G of the FMGC 1 and pins AA/7C,7D of the ATSU (Ref. ASM 46-21/05)
- install the FMGC 1 and the ATSU.
B. Do the test given in Para. 3.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 106-149, 151-199, 201-299, 301-399, ∞∞46-21-00∞∞∞∞∞∞∞∞∞∞Page 206
401-499, Aug 01/05 CES Loss of the FMGC2 FM ACARS Input Signal
1. Possible Causes
_______________
- FMGC-2 (1CA2)
- ATSU (1TX1)
- wiring of the PRINTER ACARS & ATSU DATA BUS
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION
-------------------------------------------------------------------------------
AMM 22-83-34-000-001 Removal of the FMGC (1CA1,1CA2)
AMM 22-83-34-400-001 Installation of the FMGC (1CA1,1CA2)
AMM 46-21-00-740-001 BITE Test of the ATIMS
AMM 46-21-34-000-001 Removal of the Air Traffic Service Unit (ATSU) (1TX1)
AMM 46-21-34-400-001 Installation of the Air Traffic Service Unit (ATSU)
(1TX1)
ASM 46-21/05
3. Fault Confirmation
__________________
A. Test
(1) Do the BITE test of the ATIMS (Ref. AMM TASK 46-21-00-740-001).
4. Fault Isolation
_______________
A. If the test gives the maintenance message :
FMGC2(1CA2) BUS FM ACARS/ATSU1(1TX1):
- replace the FMGC-2 (1CA2) (Ref. AMM TASK 22-83-34-000-001) and (Ref. AMM TASK 22-83-34-400-001).
(1) If the fault continues:
- replace the ATSU (1TX1) (Ref. AMM TASK 46-21-34-000-001) and (Ref. AMM TASK 46-21-34-400-001).
(a) If the fault continues:
- remove the FMGC 2 and the ATSU
- do a check and repair the wiring of the PRINTER ACARS & ATSU DATA BUS: between pins AB/12F,12G of the FMGC 2 and pins AB/7C,7D of the ATSU (Ref. ASM 46-21/05)
- install the FMGC 2 and the ATSU.
B. Do the test given in Para. 3.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 106-149, 151-199, 201-299, 301-399, ∞∞46-21-00∞∞∞∞∞∞∞∞∞∞Page 207
401-499, Aug 01/05 CES Invalid Configuration of the ATSU
1. Possible Causes
_______________
- ATSU (1TX1)
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 46-21-00-610-001 Uploading of the ATSU Software with the Multipurpose
Disk Drive Unit (MDDU) AMM 46-21-00-740-001 BITE Test of the ATIMS AMM 46-21-00-860-001 Initialization Procedure of the ATSU Router AMM 46-21-34-000-001 Removal of the Air Traffic Service Unit (ATSU) (1TX1) AMM 46-21-34-400-001 Installation of the Air Traffic Service Unit (ATSU)
(1TX1)
3. Fault Confirmation
__________________
A. Test
(1) Do the BITE test of the ATIMS (Ref. AMM TASK 46-21-00-740-001).
4. Fault Isolation
_______________
**ON A/C 151-158, 201-209,
A. If the test gives the maintenance message INVALID ATSU 中國航空網 m.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 信息系統(9)
