- with the pins of the terminal block 450VT2 section 2 of the engine 2 pylon loop B fire detector (4WD2).

 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞26-12-00∞∞∞∞∞∞∞∞∞∞Page 214
 Aug 01/04 CES (b) If the test gives the maintenance message CHECK ENG 2 FIRE LOOP

 B:

 - swap back the pins of the fire detector (3WD2) with the pins of the fire detector (4WD2).

 - do a check and if necessary, repair the wiring from the terminal block 450VT2 section 1 to the fire detector (3WD2) (Ref. ASM 26-12/01).

 1 If the wiring is correct and if the fault continues:
_

 - replace the DET-FIRE, ENG 2 PYLON LOOP A (3WD2) (Ref. AMM TASK 26-12-16-000-001) and (Ref. AMM TASK 26-12-16-400-001).
 (c) If the test gives the maintenance message CHECK ENG 2 FIRE LOOP A again:

 - swap back the pins of the fire detector (3WD2) with the pins of the fire detector (4WD2).

 (d) If the fault continues, swap the pins that follow:

 - the pins of the terminal block 450VT2 section 1 of the core loop A fire detector (4001WD1)

 - with the pins of the terminal block 450VT2 section 2 of the core loop B fire detector (4001WD2).

 (e) If the test gives the maintenance message CHECK ENG 2 FIRE LOOP

 B:

 - swap back the pins of the fire detector (4001WD1) with the pins of the fire detector (4001WD2).

 - do a check and if necessary, repair the wiring from the terminal block 450VT2 section 1 to the fire detector (4001WD1) (Ref. ASM 26-12/01).

 1 If the wiring is correct and if the fault continues:
_

 - replace the DET-FIRE, CORE LOOP A (4001WD1) (Ref. AMM TASK 26-12-17-000-041) and (Ref. AMM TASK 26-12-17-400-041).
 (f) If the test gives the maintenance message CHECK ENG 2 FIRE LOOP A again:

 - swap back the pins of the fire detector (4001WD1) with the pins of the fire detector (4001WD2).

 (g) If the fault continues, swap the pins that follow:

 - the pins of the terminal block 450VT2 section 1 of the fan loop A fire detector (4000WD1)

 - with the pins of the terminal block 450VT2 section 2 of the fan loop B fire detector (4000WD2).

 (h) If the test gives the maintenance message CHECK ENG 2 FIRE LOOP

 B:

 - swap back the pins of the fire detector (4000WD1) with the pins of the fire detector (4000WD2).
 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞26-12-00∞∞∞∞∞∞∞∞∞∞Page 215
 Aug 01/04R CES

 - do a check and if necessary, repair the wiring from the terminal block 450VT2 section 1 to the fire detector (4000WD1) (Ref. ASM 26-12/01).
 1 If the wiring is correct and if the fault continues:
_

 - replace the DET-FIRE, FAN LOOP A (4000WD1) (Ref. AMM TASK 26-12-15-000-042) and (Ref. AMM TASK 26-12-15-400-042).
 (i) If the test gives the maintenance message CHECK ENG 2 FIRE LOOP A again:

 - swap back the pins of the fire detector (4000WD1) with the pins of the fire detector (4000WD2).

 (j) If the fault continues:

 - disconnect the connector 2WD2-A from the engine 2 FDU (2WD2)
 - on the connector, on the wiring side, make sure that the equivalent resistance value between pins J and K is between 1425 ohms and 1575 ohms.
 (k) If the equivalent resistance value is not correct and is: between 2137 ohms and 2363 ohms: there is one defective detector between 4275 ohms and 4725 ohms: there are two defective detectors infinite: there is either three defective detectors or a defective wiring.
 - disconnect the electrical harness from the three loop A fire detectors
 - on the responder of each detector, make sure that the resistance value is between 4275 ohms and 4725 ohms: . between pins A and D for the engine 2 pylon loop A fire detector (3WD2) and the fan loop A fire detector (4000WD1), . between pins A and C for the core loop A fire detector (4001WD1).
 1 If the resistance value is not correct:
_

 - replace the related fire detector: . for DET-FIRE, ENG 2 PYLON LOOP A (3WD2) (Ref. AMM TASK 26-12-16-000-001) and (Ref. AMM TASK 26-12-16-400-001) . for DET-FIRE, FAN LOOP A (4000WD1) (Ref. AMM TASK 26-12-15-000-042) and (Ref. AMM TASK 26-12-15-400-042) . for DET-FIRE, CORE LOOP A (4001WD1) (Ref. AMM TASK 26-12-17-000-041) and (Ref. AMM TASK 26-12-17-400-041).

 - connect the electrical connector 2WD2-A to the engine 2 FDU.

 2 If the resistance value is correct:
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 FIRE PROTECTION 防火(32)