(2) If the operational test of the automatic change-over function does not give the maintenance message AFS: FAC2/RT ENGD CHG-OV:
- replace the FAC-1 (1CC1), (Ref. AMM TASK 22-66-34-000-002) and (Ref. AMM TASK 22-66-34-400-002).
(a) If the fault continues:
- do a check and repair the wiring of the RUD TR OWN ENGD COM and RUD TR OWN ENGD MON discretes (from the FAC 1 (1CC1) to the first terminal block), (Ref. ASM 22-68/03).
B. Do the test given in Para. 3.A.(1).
Loss of the Reception of the RT ENGD Feedback Discrete by the FAC 2
1. Possible Causes
_______________
- FAC-2 (1CC2)
- wiring of the RUD TR ENGD COM and RUD TR ENGD MON discretes (from the FAC 2 (1CC2) to the first terminal block)
- wiring of the RUD TR OWN ENGD COM and RUD TR OWN ENGD MON discretes (from the FAC 2 (1CC2) to the first terminal block)
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 22-60-00-710-002 Operational Test of the Automatic Change-Over
Function
AMM 22-66-34-000-002 Removal of the FAC (1CC1,1CC2)
AMM 22-66-34-400-002 Installation of the FAC (1CC1,1CC2)
AMM 22-96-00-710-001 Operational Test of the AFS
ASM 22-68/03
3. Fault Confirmation
__________________
A. Test
(1) Do the operational test of the AFS (Ref. AMM TASK 22-96-00-710-001) and read the result for the FAC 2.
(2) Do the operational test of the automatic change-over function (Ref. AMM TASK 22-60-00-710-002).
4. Fault Isolation
_______________
A. If the operational test of the AFS gives the maintenance message AFS: FAC2/RT ENGD FDBK:
(1) If the operational test of the automatic change-over function gives the maintenance message AFS: FAC1/RT ENGD CHG-OV:
- replace the FAC-2 (1CC2), (Ref. AMM TASK 22-66-34-000-002) and (Ref. AMM TASK 22-66-34-400-002).
(a) If the fault continues:
- do a check and repair the wiring of the RUD TR ENGD COM and RUD TR ENGD MON discretes (from the FAC 2 (1CC2) to the first terminal block), (Ref. ASM 22-68/03).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞22-62-00∞∞∞∞∞∞∞∞∞∞Page 211
Feb 01/98 CES
(2) If the operational test of the automatic change-over function does not give the maintenance message AFS: FAC1/RT ENGD CHG-OV:
- replace the FAC-2 (1CC2), (Ref. AMM TASK 22-66-34-000-002) and (Ref. AMM TASK 22-66-34-400-002).
(a) If the fault continues:
- do a check and repair the wiring of the RUD TR OWN ENGD COM and RUD TR OWN ENGD MON discretes (from the FAC 2 (1CC2) to the first terminal block), (Ref. ASM 22-68/03).
B. Do the test given in Para. 3.A.(1).
Loss of the Rudder Trim Function on the FAC 1
1. Possible Causes
_______________
- ACTUATOR-RUDDER TRIM (10CC)
- RELAY-RUD TRIM 1 (7CC1)
- FAC-1 (1CC1)
- wiring for 28VDC signal (pin A2) and GND signal (pin X2) at the relay (7CC1)
- wiring of the RUD TR ACT VALID signal from the FAC1 to the RT actuator and
associated GND at the RT actuator R - electronic module
- wiring of the RUD TR ACT PWR ON signal from the FAC1 to the relay 7CC1
- wiring of the 28VDC signal from the relay 7CC1 to the RT actuator (10CC) and associted GND at RT actuator
- wiring from the FAC 1 (1CC1) to the rudder trim actuator (10CC)
- wiring of the RUD TR V1 and RUD TR V2 discretes from the rudder trim actuator (10CC) to the FAC 1 (1CC1)
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 22-62-00-710-001 Operational Test of the Rudder Trim Function
AMM 22-66-34-000-002 Removal of the FAC (1CC1,1CC2)
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 AUTO FLIGHT 自動飛行1(96)
