1. Possible Causes
_______________

 - SEAT-CAPTAIN (3MS)

 - SEAT-F/O (4MS)

 - SW-CONSOLE/FLOOR (15LE)

 - wiring from the Captain seat (3MS) to the switch (15LE)

 - wiring from the Captain Seat (3MS) to the ground

 - SW-CONSOLE/FLOOR (16LE)

 - wiring from the F/O seat (4MS) to the switch (16LE)

 - wiring from the F/O seat (4MS) to the ground

 2. Job Set-up Information
______________________
 A. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 25-11-51-000-001 Removal of the Captain/First Officer Seat (3MS, 4MS) AMM 25-11-51-400-001 Installation of the Captain/First Officer Seat (3MS,
 4MS) AMM 33-12-00-710-001 Operational Test of the General Illumination ASM 25-11/01 ASM 33-12/01
 3. Fault Confirmation
__________________
 A. Test

 (1) Do the operational test of the general illumination (Ref. AMM TASK 33-12-00-710-001).
 NOTE : Do the test of the console and the briefcase lights only.
____

 一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一 EFF : ALL ∞∞25-11-00∞∞∞∞∞∞∞∞∞∞Page 219
 Aug 01/05R
 CES

 4. Fault Isolation
_______________

 A. If during the operational test:
 (1) A bulb is inoperative:

 - replace the bulb.

 (2) The Captain floor lighting is inoperative:

 - disconnect the plug 1197VC and make sure that there is 28VDC at pins F and G (Ref. ASM 25-11/01).
 (a) If there is 28VDC at pins F and G:

 - replace the SEAT-CAPTAIN (3MS) (Ref. AMM TASK 25-11-51-000-001) and (Ref. AMM TASK 25-11-51-400-001).

 (b) If there is no 28VDC at pin F:

 - replace the SW-CONSOLE/FLOOR (15LE).
 1 If the fault continues:
_

 - do a check and repair the wiring from the Captain seat (3MS) to the switch (15LE) pins 1B, 1C, 2C and 3B (Ref. ASM 33-12/01).
 (c) If there is no ground at pin G:
 - do a check and repair the wiring from the Captain Seat (3MS) to the ground (Ref. ASM 33-12/01).
 (3) The First Officer floor lighting is inoperative:
 - disconnect the plug 1198VC and make sure that there is 28VDC at pins F and G.
 (a) If there is 28VDC at pins F and G:

 - replace the SEAT-F/O (4MS) (Ref. AMM TASK 25-11-51-000-001) and (Ref. AMM TASK 25-11-51-400-001).

 (b) If there is no 28VDC at pin F:

 - replace the SW-CONSOLE/FLOOR (16LE).
 1 If the fault continues:
_

 - do a check and repair the wiring from the F/O seat (4MS) to the switch (16LE) pins 1B, 1C, 2C and 3B (Ref. ASM 33-12/01).
 (c) If there is no ground at pin G:
 - do a check and repair the wiring from the F/O seat (4MS) to the ground (Ref. ASM 33-12/01).
 B. Do the test given in Para. 3.
 一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一 EFF : ALL ∞∞25-11-00∞∞∞∞∞∞∞∞∞∞Page 220
 Aug 01/05 CES

 PASSENGER COMPARTMENT SEATS - FAULT ISOLATION PROCEDURES
________________________________________________________
 TASK 25-21-00-810-801

 The ON lamp of the PED switch does not come on
 1. Possible Causes
_______________
 - PED (53HP)

 - 56HP

 - lamp

 - Aircraft wiring

 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
 -------------------------------------------------------------------------------
No specific 1 MULTIMETER - STANDARD
 B. Referenced Information
 -------------------------------------------------------------------------------
REFERENCE DESIGNATION
 -------------------------------------------------------------------------------
ASM 25-21/00
 TSM 25-21-00 P.Block 301 PASSENGER COMPARTMENT SEATS

 3. Fault Confirmation
__________________

 A. Push the PED POWER switch (56HP) to ON (Ref. TSM 25-21-00 P.Block 301).
 4. Fault Isolation
_______________
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual EQUIPMENT/FURNISHINGS(11)