External Hardware - LH Side
 Figure 403/TASK 73-11-40-991-304- 23 (SHEET 2)
 F EEFF :  ALL  『E 73-11-40 Page 413 
E  E  Feb 01/98
 E  E
 ECES  E

 External Hardware - LH Side
 Figure 403/TASK 73-11-40-991-304- 33 (SHEET 3)
 F EEFF :  ALL  『E 73-11-40 Page 414 
E  E  Feb 01/98
 E  E
 ECES  E

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E

 INTENTIONALLY BLANK

 F 『 E E Page 41573-11-40
 E E Feb 01/98 E E ECES E F 『 E C F M E E E E 56-5B E F 『 E C F M E E E E 56-5B E F 『 E C F M E E E E 56-5B E F 『 E C F M E E E E 56-5B E

 External Hardware - RH Side
 Figure 404/TASK 73-11-40-991-305- 14 (SHEET 1)
 F EEFF :  ALL  『E 73-11-40 Page 416 
E  E  Feb 01/98
 E  E
 ECES  E

 External Hardware - RH Side
 Figure 404/TASK 73-11-40-991-305- 24 (SHEET 2)
 F EEFF :  ALL  『E 73-11-40 Page 417 
E  E  Feb 01/98
 E  E
 ECES  E

 External Hardware - RH Side
 Figure 404/TASK 73-11-40-991-305- 34 (SHEET 3)
 F EEFF :  ALL  『E 73-11-40 Page 418 
E  E  Feb 01/98
 E  E
 ECES  E

 External Hardware - RH Side
 Figure 404/TASK 73-11-40-991-305- 44 (SHEET 4)
 F EEFF :  ALL  『E 73-11-40 Page 419 
E  E  Feb 01/98
 E  E
 ECES  E

 F 『
 E C F M E
 E E
 E 56-5B E
 E E
 NOTE : At some positions, manifold hinge brackets or engine plumbing

____ brackets are installed with the fuel nozzle. It is necessary to remove these brackets for removal of the fuel nozzle. Identify the bolts and brackets by position number and keep the bolts and the brackets for each nozzle position together to ease the installation of the fuel nozzle.
 (2) Cut and remove the lockwire from the bolts (10, 50) that attach the fuel nozzle(s) to be removed to the combustion case.

 (3) Apply a small amount of liquid wrench (Material No. CP2162) to the bolts (10), (50) that attach the fuel nozzle(s) to be removed to the combustion case. Permit the Liquid Wrench to soak for approximately 5 minutes.

 (4) Put a container 1 l (0.25 USgal) below the fuel nozzle(s) to be removed to catch any fuel leakage.

 (5) To remove the fuel nozzles, start at the steps shown on the following reference table:

 ------------------------------------------------------------------------------FUEL O'CLOCK START NOZZLE POSITION HARDWARE AT POS. NO. ALF TO REMOVE STEP ------------------------------------------------------------------------------
1 2 4 5  12:00 12:30 2:00 2:30  Engine bleed air duct Bracket Hinge bracket (move)Hinge bracket (move) None  4.A (6)4.A (9)4.B.4.B.
 6 7 8 9 10 11  3:00 3:30 4:00 5:00 5:30 6:00  LPTACC tube Support bracket assembly Hinge bracket (move)LPTACC tube RH Spark igniter RH Ignition lead (move) LPT cooling bracket Hinge bracket (move)RH Spark igniter RH Ignition lead (move)RH Spark igniter RH Ignition lead (move)None  4.A (8)4.A (8)4.A (7)4.A (7)4.A (7)4.B.
 12  6:30  LH Spark igniter LH Ignition lead (move) Start bleed tube 4.A (7)

 F 『 EEFF : ALL E Page 42073-11-40
 E E Feb 01/98 E E ECES E

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E

 ------------------------------------------------------------------------------
FUEL  O'CLOCK  START
 NOZZLE  POSITION  HARDWARE  AT
 POS. NO.  ALF  TO REMOVE  STEP

 ------------------------------------------------------------------------------Hinge bracket (move)
 13  7:00 LH Spark igniter 4.A (7) LH Ignition lead (move) LPT cooling bracket

 14  8:00 LH Spark igniter 4.A (7) LH Ignition lead (move) Hinge bracket (move)

 15 8:30  Engine bleed air duct 4.A (6)

 16 9:00  Engine bleed air duct 4.A (6)

 17  9:30 Engine bleed air duct 4.A (6) Bracket 18 10:00 LPT cooling bracket 4.A (7)
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM 發動機燃油和控制 ENGINE FUEL AND CONTRO(56)