(4)
TORQUE the castle nut (2) to between 0.7 and 0.8 m.daN (61.94 and
70.79 lbf.in) and safety it with a new cotter pin (1).
(5)
Seal the connection with the SEALANTS (Material No. 09-016) and apply the PAINTS FOR DETAIL (INTERNAL AND EXTERN AL) (Material No. 07-001).
(6)
Connect the air intake flap with the bolt (10), the washers (15), (9A) and the castle nut (16). Do not fully tighten the nut at this time.
(7)
Remove the blanking cap and connect the electrical connector (18) and safety it with lockwire-corrosion resistant steel 0,8 mm.
(8)
Connect the bonding jumper (21) with the screw (20) and the washer (19).
(9)
Seal the connection with the SEALANTS (Material No. 09-016) and apply the PAINTS FOR DETAIL (INTERNAL AND EXTERN AL) (Material No. 07-001).
Subtask 49-16-51-710-050
C. Do the adjustment of the air-intake flap actuator (4015KM) (Ref. TASK 49-16-51-820-001).
Subtask 49-16-51-865-051
D. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------121VU APU/APU/CTL 2KD L42 121VU APU/ECB/SPLY 1KD L41
Subtask 49-16-51-420-051
E. Final Installation
(1)
TORQUE the castle nut (16) to between 0.7 and 0.8 m.daN (61.94 and
70.79 lbf.in) and safety it with a new cotter pin (17).
(2)
Seal the connection with the SEALANTS (Material No. 09-016) and apply the PAINTS FOR DETAIL (INTERNAL AND EXTERN AL) (Material No. 07-001)
(3)
Install the clamp (11) and connect the bellows (12) to the air-intake flap actuator (6).
5. Close-up
________ Subtask 49-16-51-410-050
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Install the catwalk panel on the service panel with the 22 stud fasteners.
(3)
Close the maintenance door 314AR.
(4)
Remove the access platform(s).
Subtask 49-16-51-865-052
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 1KD, 2KD.
TASK 49-16-51-820-001
Adjustment of the Air-Intake Flap Actuator (4015KM) (GTCP 36-300)
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
No specific access platform 2.5 m (8 ft. 2 in.)
No specific Torque Wrench : range 0.00 to 1.20 m.daN
(0.00 to 9.00 lbf.ft)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
No specific lockwire-corrosion resistant steel 0.8mm
Material No. 07-001 ELECTRICAL BONDING COATING (BLUE COLOR) (Ref. 20-31-00)
Material No. 09-016 USA MIL-PRF-81733D TYPE II CLASS B CORROSION INHIBITING FILLET CONSISTENCY (Ref. 20-31-00)
C. Expendable Parts
-------------------------------------------------------------------------------FIG.ITEM |DESIGNATION |IPC-CSN -------------------------------------------------------------------------------
cotter pin 49-16-04 03 -070
D. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機(jī)維護(hù)手冊 AMM 機(jī)載輔助動力 AIRBORNE AUXILIARY POWER3(45)
