4. Procedure
_________ R **ON A/C 001-049, 051-099, 101-105, 201-203,
Subtask 31-21-00-750-050
A. Adjustment of the Clock NOTE : When you set the time or the date, only the related numbers
____
change. The other digits remain unchanged.
The number increases every second.
(Ref. Fig. 501/TASK 31-21-00-991-001)
-------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
1.
Setting the hours On the clock, set the UTC switch
(right lower corner) from the RUN position to the HSD position.
2.
When the correct number for the hours is reached, set the UTC
switch to the MSM position.
3.
When the correct number for the minutes is reached, set he UTC switch to the HLDY position.
4.
Check these numbers: if they are not correct go back to step 1. If they are correct proceed to the following step:
5.
Set the UTC selector switch to RUN.
The two left digits of the upper window
start counting
(Ref. Fig. 501/TASK 31-21-00-991-001)
(item 1).
The two right digits of the upper
window start counting
(Ref. Fig. 501/TASK 31-21-00-991-001)
(item 2).
The numbers for the hours and for the
minutes stand frozen.
The last right digit (tenth of minutes)
starts counting while the numbers for
the hours and minutes stand frozen
until the right digit is reset.
1EFF : ALL 1 31-21-00Page 503 1 1 May 01/05 1 1 1CES 1
Clock
Figure 501/TASK 31-21-00-991-001
R 1EFF : 001-049, 051-099, 101-105, 201-203, 1 31-21-00Page 504 1 1 May 01/05 1 1 1CES 1
-------------------------------------------------------------------------------
ACTION RESULT -------------------------------------------------------------------------------
6. Setting the date. Press the DATE pushbutton switch once and set the UTC switch to the HSD position.
When the figure for the days is reached, set the UTC switch to MSM.
When the figure for the months is reached, set the UTC switch to HLDY.
When the figure for the years is reached, set the UTC switch to RUN.
Press the DATE pushbutton switch once.
The days and months on the upper
window, then the year is displayed in
turn.
The number for the days stand frozen
while the number for the months starts
counting.
The numbers for the days and months are
frozen while the number for the year
starts counting.
The date is displayed (days, months,
and year).
The time of the day is displayed with
the last smaller digit of the window
counting every 6s.
The clock is set.
R **ON A/C 106-149, 151-199, 201-299, 301-399, 401-499, Post SB 31-1133 For A/C 201-203, Subtask 31-21-00-750-050-A
A. Setting of the clock internal time base NOTE : When you set the time or the date, only the digits which are
____
flashing can change, the other digits remain unchanged. (Ref. Fig. 501A/TASK 31-21-00-991-001-A)
1EFF : ALL 1 31-21-00Page 505 1 1 Aug 01/05 1 1 1CES 1
Clock Figure 501A/TASK 31-21-00-991-001-A
R 1EFF : 106-149, 151-199, 201-299, 301-399, 1 31-21-00Page 506 1401-499, 1Aug 01/05 1 1 1CES 1
-------------------------------------------------------------------------------
ACTION RESULT -------------------------------------------------------------------------------
1. Setting the minutes On the clock face, set the
GPS/INT/SET (right middle section of the clock face) to the SET position.
Increase (or decrease) the figure by turning the SET knob clockwise (or counterclockwise).
2.
Setting the hours Press the SET knob once
3.
Increase (or decrease) the figure for the hours by turning the SET knob clockwise (or counterclockwise).
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM 指示/記錄系統INDICATING/RECORDING SYSTE(82)
