曝光臺 注意防騙 網(wǎng)曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

(rms) value of the analyscr noise floor in the octave band with
thc higl-lest ~loiscfl oor; and anplitudc rcspo1u.c ovcr tl* uppcr
40 dB rangc should be lincnr to within iO.5 dB.
4.3.2.4.2 Mean-squarc sound pressures should be lime
averaged by integrat~on of the squared output of frequency
band filters over an ~ntegrationi nterval that should be no less
than 8 s. Alt data should be processed within the frequency
range from 45 Hz to 11 200 Hz. Data should bc corrected for
all known or predictable errors, such as deviations of system
frequency response from a flat response.
4.3.2.5 Total system
4.3.2.5.1 In addition to speclficalions for component
systems. frequency response of the combincd data acquisition
and reduction system sbould be flnt within *3 dB ovcr the
frequency range from 45 Hz to 11 200 Hz. Frequency response
gradient anywhere within this range should not cxcced 5 dB
per octave.
4.3.2.5.2 Arnplitudc resolution should he at least 1.0 dB.
Dynamic range should be a minimum of45 dB between full
scale and the rms value of the system nolse floor in the
frequcncy band with the highest nose floor. Amplitude
response should be lrncar w i t h M.5 dB over the upper 35 dB
in each frequency band.
4.3.3 Meteomlogical
The wind speed should be measured with a device having a
range of at least 0 to 28 kdh (0 to 15 kt) with an accuracy of
at lcast *2 kkmih (-L L kt). Temperature measurcmcnts should be
mndc with a device having a range of at lcast 0°C to W°C with
nn accuracy of at least +O.SDC. Relative humicbty should be
measured with a devrce having a range of O to 100 per
cent with an accuracy of at least k5 percenlsge points.
Atmospheric pressure sbould be measured with a dev~ce
having a range of at lcast ROO to 1 I00 hPa w~tha n accuracy
of at lcast C3 hPa.
4.4 Tcst procedure
4.4.1 Tesl conditions
4.4.1.1 Ambient noise measurements should be made m
sufficient number to be represenatwe for all acoustic measurement
stations. providmg comction data to apply to measured
APU noise where necessary (see 4.4.4).
4.4.1.2 Tk installed APU should mect thc noise levels
specified In 3.1 at the points specified under typrcal loads, up
to and including thosc imposed by the electric power generator
and air-cnndrtioning units and any other associated systems at
thclr nonnal maximum continuous ground opcrrrtion power
rcquircmc~i~s.
2411 1/05 ATT C-4
Aaachmenr C Annex 16 - Environmental Protection
Note. - A memuremeni of norsejiom a pcmicrrZar model of
a~rxiliqpo wer ini it instolled in a spec$c oirrraJ ype shotfil
no! be deemed 9.pical of the same eqrtipmenf insinlkd in orher
aitrmfl vpes nor of ori~erm rdels of APU instolled in the same
aircvofl Qpt.
4.4.2 Acoustical measurement locations
4.4.2.1 Except where specified Mhenvise, noise measurements
should be made with microphones at 1.6 In * 0.025 rn
(5.25 ft * 1.0 in) above the ground or surface where passengers
or servicing personnel may stand, wilh the microphone
diaphragm parallel to the ground and facing upwards.
4.4.2.2 Locations for measuring noise shwld be as follows:
a) curgo door locations: measurements should be made at
each cargo Jmr l~rr[io~wri,t lr 01t:d wll opal, whilt: d~t:
aucraft is in a typicai ground handling configuration.
These mcasuremcnts should bc takcn at the cmtre of thc
opening, in tbe plane of the fuselage skin;
b) pmsenger dour loca~ions: measurements should be
made at each pawnger entry door. with the door open,
on the vertical centre line of the opening, in tbe plane of
the fuselage skin;
c) servicing locdonr: measurements should be made at all
servicing positions wbere persons are normally working
dwing aircraft ground handling operations, these
positions to be determined by reference to tbe approved
aircraft operating and service manuals;
d) m ylm fiom: apprDpnate measurement positions
should br cbosxn along the sides of a reciartgle centred
MI the test aircraft as illustrated in Figure C-2. The
distance between measurement positions should nor be
greater than 1 0 m for large aimaft. This distance may be
reduced to accommodate small aeroplanes or to fulfil
special requirements.
a surnmation of mean-square sound pressures in appropriate
one-third octave bands. Overall sound pressure levels should
be determined frorn a surnrnafion of mean-square sound
pressures in the 24 one-third octave. or 8 one octave.
frequency bands included in the fiuency range frorn 45 Hz
to l l 200 Hz.
4.4.4.2 Qwrall sound pressure levels, A-weighted
sound levels and one-third or one octave band data should be
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：附件16--環(huán)境保護an16_v1_4ed(83)