曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

key located at the bottom of the RMU. When the STO key is depressed,
the nomenclature below the preset COM frequency will change back to
MEMORY, and the digit following MEMORY will indicate in which
memory location the frequency is stored. With the main tuning page
displayed, the rotary tuning knob can be used to scroll through the frequencies
stored in memory. As each memory location (channel) is selected,
the stored frequency will be shown on the COM preset line
which can then be moved to the active position by depressing the transfer
key.
Pilot’s Manual
5-54 PM-132A
A TX will appear at the top of the COM window when the associated
radio is transmitting. Its purpose is to show that the transmitter is on
and to alert the pilot in case of a stuck microphone key. If not attended
to for approximately two minutes, a beep will sound on the audio and
a MIC STK annunciation will appear at the top of the COM window
until the microphone button is released. Ten seconds after the MIC STK
annunciation appears, the selected transmitter will automatically turn
off. Depressing the SQ (squelch) function button at the bottom of the
RMU causes the COM radio to open its squelch and allows any noise
or signal present in the receiver to be heard. When selected, a SQ will
appear at the top of the COM window. Pressing the button a second
time closes the squelch.
FMS TUNING
The FMS interfaces with the RMUs for radio tuning. The FMS has a radio
tuning page that can be used to control VHF COM, NAV, ADF and
transponder codes. If it is suspected that the FMS is interfering with
com/nav radio tuning, an FMS ENABLE/DISABLE selection on the
RMU NAV memory page can be toggled with the adjacent line select
key. The DISABLE selection will prevent tuning any of the radios
through the FMS CDU.
NAV TUNING
The format of the NAV window (top right corner of the RMU) is identical
to the COM window in that the top frequency is active and the bottom
frequency is the preset frequency. Pressing the line select key
alongside the NAV preselect window moves the cursor to that window.
This connects the tuning knobs to the NAV preset frequency. By pressing
the NAV transfer key (top right) the preset and active frequencies
are exchanged. The preset frequency may be changed to a different frequency
by using the tuning knobs or by pressing the line select key to
bring up the next frequency from memory. Selection of stored frequencies
can be accomplished by pressing the line select key by the NAV
preset window until the tuning box encloses the memory mnemonic.
Rotating the tuning knob scrolls through the stored frequencies displaying
them in the preset area.
Pilot’s Manual
PM-132A 5-55
The memory functions and direct tuning operate the same as described
under COM operation, except the NAV window has an added function
called DME split tuning mode. Its operation is similar to the function
called DME hold. Depressing the DME function button on the RMU allows
the DME frequency to be tuned independent of the NAV frequency.
Depressing the DME once causes the NAV window to split into two
sections, the top one being the active VOR frequency and the lower one,
now labeled DME, containing the active DME frequency in VHF format.
In this condition, the DME may be tuned directly by simply pressing
the line select key to place the cursor box around the frequency and
retuning using the tuning knobs. The DME digital station identifier will
appear adjacent to the DME nomenclature on the top edge of the DME
window. An amber H (hold) appears in the lower DME window. This
indicates that the distance display (DME or TACAN) is not paired with
the VOR/ILS navigation data. When the H is displayed on the RMU, it
will also be displayed following the DME read-out on the PFD.
ADF TUNING
ADF operation is the same as COM and NAV tuning in that depressing
the line select key beside the ADF frequency will place the cursor over
the frequency to be changed. Rotating the small tuning knob slowly
will advance the frequency in 0.5 kHz steps. This change will increase
to 10 kHz steps when the large knob is used. The RMU has the capacity
to store one ADF frequency in memory. This is done by selecting the desired
frequency, then depressing the STO function key at the bottom of
the RMU. To retrieve the stored frequency from memory, the frequency
line select key must be depressed for two seconds. ADF modes are also
controlled within the ADF window. Repetitively depressing the line select
key adjacent to the ADF mode annunciator will step through the
available ADF modes of operation. This can also be accomplished by
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：BOMBARDIER_Learjet_0-Flight_Controls_and_Avionics(25)