曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

two CPCs.
The automatic controller performs the following functions:
• Automatic control of cabin altitude, rate regulation and rate limitation.
• Ditching sequence.
• Door open protection.
• Generating outputs for EICAS display and messages.
• CAIMS function and interface.
AUTO mode is dependent upon the following information:
• Airplane altitude, vertical speed and barometric correction received from ADCs and DAUs or
scheduled flight information from FMS when available.
• Landing elevation from FMS when available, or directly selected from the switch on the
cabin pressure control panel.
• Rate limit selection from cabin pressure control panel.
• Weight on wheels and door open position from Landing Gear Electronic Control Unit
(LGECU).
• Engine throttle position from Electronic Engine Controllers (EEC).
FGF0210_017
DAU
3
ADC
1
DAU
1
DAU
2
ADC
2
DAU
4
MANUAL
MANUAL
CABIN
PRESSURE
CONTROLLER 1
CABIN
PRESSURE
CONTROLLER 2
FMS
LGECU
EEC
CONTROL
PANEL
OUTFLOW
VALVE 1
OUTFLOW
VALVE 2
SAFETY
VALVE 2
LIM
LIM
AUTO 1
AUTO 1
MAN
MAN
AUTO 2
AUTO 2
SAFETY
VALVE 1
AIR CONDITIONING AND PRESSURIZATION
Rev 12, Aug 14, 2006 Flight Crew Operating Manual
CSP 700−5000−6
Volume 2
02−10−41
MODES OF OPERATION (CONT'D)
Automatic Mode (Cont’d)
The PRIMARY mode uses information from the FMS to minimize cabin altitude pressure rate and
maximize cabin comfort. In primary mode the CPC uses time to go, time to top of climb, cruise
flight level and landing information from the FMS to compute the cabin pressurization schedule for
the flight. The CPCS operates in primary mode when FMS information has been programmed and
the landing elevation source is selected on FMS. In all other cases, the system defaults to
secondary mode.
SCHEDULED CRUISE ALTITUDE
AIRPLANE
CABIN CRUISE ALTITUDE
CABIN RATE OF DESCENT
ELEVATION
TIME TO GO
CABIN
TIME TO
TOP OF CLIMB
(TOC)
GF0210_048
ALTITUDE
ALTITUDE
LANDING
In SECONDARY mode the CPC uses the airplane pressure altitude and vertical speed to compute
the pressurization schedule for the flight. The secondary mode requests the landing elevation to
be selected on the cabin pressurization control panel if it has not been entered. The system will
also enter the secondary mode if the LAND ELEV selector was changed to the MAN position.
In either AUTO mode, the CPC controls the cabin pressure through the opening of both electrical
outflow valves.
Only one AUTO system is in operation while the other AUTO system is in active standby. Transfer
from one AUTO system to the other automatically occurs each day (CPC 1 on odd days, CPC 2 on
even days). With FMS information available to the CPC, cabin altitude and cabin altitude rate
control are automatic, during ground and flight sequences.
In case of a failure of the active system, manual transfer from one CPC to the other can be
accomplished by sequencing the AUTO/MAN switch located on the Pressurization control panel,
from AUTO to MAN then back to AUTO.
Transferring to alternate AUTO control when operating around high elevation airfield (with landing
elevation ≥5,670 feet) may cause cabin pressure drifting to max cruise cabin altitude (i.e.
5,670 feet) before returning to normal cabin pressure schedule. This drift is caused by mismatch of
CPC operating sequence between AUTO control due to sensor tolerance.
AIR CONDITIONING AND PRESSURIZATION
Flight Crew Operating Manual Rev 12, Aug 14, 2006
CSP 700−5000−6
Volume 2
02−10−42
MODES OF OPERATION (CONT'D)
Automatic Mode (Cont’d)
Effectivity:
• Airplanes 9127 thru 9158 not incorporating Service Bulletin:
• SB 700−1A11−21−004, Modification − Pressurization Control − Cabin Altitude Reduction
During Flight for Improved Passenger Comfort.
Transferring to alternate AUTO control when operating around high elevation airfield (with landing
elevation ≥7,230 feet) may cause cabin pressure drifting to max cruise cabin altitude (i.e.
7,230 feet) before returning to normal cabin pressure schedule. This drift is caused by mismatch
of CPC operating sequence between AUTO control due to sensor tolerance.
In case of unannounced system malfunction, operate system with manual control.
Automatic Pre-Pressurization Sequence On Ground
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：Bombardier_Global_000-Air_Cond_and_Press(15)