曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

-Turn the DATA knob or push the PUSH SELECT button to select marker sense mode LO or HI.
- Select the NAV TEST mode.
-Turn the MENU knob to move the selection box to the TEST control.
-Turn the DATA knob or push the PUSH SELECT button to select the TEST mode.
NAVIGATION
Volume 2 Flight Crew Operating Manual May 06/2005
17-01-04 CSP 100-6 REV 2
VHF NAVIGATION SYSTEM (Cont)
TRANSPONDER/TCAS OPERATION
The radio menu provides basic transponder and TCAS control. The TRANSPONDER/TCAS CONTROL menu provides
control display for other transponder and TCAS operations. The active beacon code, TCAS mode, and TCAS altitude limits
selection that show on the left of the TRANSPONDER/TCAS CONTROL menu are identical to the TRANSPONDER/
TCAS display on the radio menu. Two transponders are installed. The active transponder selection is used to select the desired
transponder. When the active transponder is set to ATC 1, the pilot’s side transponder is active. When the active transponder
is set to ATC 2, the copilot’s side transponder is active.
To tune the TRANSPONDER/NAV radio execute the following steps:
1. Push the RADIO button on the DCP to show the radio menu on the MFD if another menu/list is active.
2. Turn the MENU knob on the DCP to move the selection box to the TRANSPONDER/TCAS display on the radio
menu.
3. Push the RADIO button on the DCP to show the TRANSPONDER/TCAS CONTROL menu on the MFD.
4. The following operations are performed on the TRANSPONDER/TCAS CONTROL menu:
- Select TCAS traffic altitude mode.
-Turn the MENU knob to move the selection box to the TRAFFIC control
-Turn the DATA knob or push the PUSH SELECT button to select traffic altitude mode REL (relative) or ABS
(absolute)
- Select the active transponder.
-Turn the MENU knob to move the selection box to the transponder control
-Turn the DATA knob or push the PUSH SELECT button to select ATC 1 or ATC 2 as the active transponder
- Set the Flight ID
-Turn the MENU knob to move the selection box to the Flight ID control
-Turn the TUNE knobs to set the desired Flight ID characters
- Select the ATC/TCAS TEST mode.
-Turn the MENU knob to move the selection box to the TEST control
-Turn the DATA knob or push the PUSH SELECT button to select the TEST mode
ADF RADIO OPERATION
The radio menu provides basic ADF radio tuning. The ADF CONTROL menu provides control display for other ADF radio
operations. Each ADF radio installed on the aircraft has its own ADF CONTROL menu. If only one ADF radio is installed,
it shows on both the on-side and cross-side menus, and will be labeled ADF CONTROL with no numerical designator. The
active frequency, recall frequency, and antenna mode that show on he left of the ADF CONTROL menu are identical to the
ADF display on the radio menu.
To set the ADF modes execute the following steps:
1. Push the RADIO button on the DCP to show the radio menu on the MFD if another menu/list is active.
2. Turn the menu knob on the DCP to move the selection box to the ADF radio (ADF 1 or ADF 2) display on the
radio menu.
3. Push the RADIO button on the DCP to show the ADF CONTROL menu on the MFD.
4. The following operations are performed on the ADF CONTOL menu:
- Select the ADF/ANT mode.
-Turn the MENU knob to move the selection box to the MODE control
-Turn the DATA knob or push the PUSH SELECT button to select ADF or ANT mode
- Select BFO mode.
-Turn the MENU knob to move the selection box to the BFO control
-Turn the DATA knob or push the PUSH SELECT button to select ON or OFF for the BFO mode
- Select ADF TEST mode.
-Turn the MENU knob to move the selection box to the TEST control
-Turn the DATA knob or push the PUSH SELECT button to select the TEST mode
V 2
NAVIGATION
Sep 13/2004 Flight Crew Operating Manual Volume 2
REV 1 CSP 100-6 17-01-05
VHF NAVIGATION SYSTEM (Cont)
TUNING REVERSION
Normally, the MFD provides the master tuning control. However, if the MFD fails or is reverted to a compressed PRF format,
radio tuning through that MFD is no longer available. Tuning reversion allows the pilot to select either the MFD or
the CDU as the master tuning control. When the TUNE knob on the Reversion Selection Panel is set to MFD ONLY or
when the TUNE knob is set to CDU ONLY, the CDUs ignore tuning commands from the MFDs and the MFD radio menu
is blanked. When the TUNE knob is in the COM 1 121.50 position, tuning is as normal (MFD is the master tuning control),
but the COM 1 radio is forced to the emergency 121.50.
1. Turn the TUNE knob on the REVERSION panel to the desired position.
- The MFD ONLY position selects the MFDs as the only tuning control
- The CDU ONLY position selects the CDUs as the only tuning control
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：Bombardier_Challenger_Global_00-Navigation(4)