曝光臺 注意防騙 網(wǎng)曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
ÏÏÏÏÏÏÏ
ÏÏÏÏÏÏÏ
ÏÏÏÏÏÏÏ
ÏÏÏÏÏÏÏ
ÏÏÏÏÏÏÏ
ÏÏÏÏÏÏÏ
ÏÏÏÏÏÏÏ
ÏÏÏÏÏÏÏ
ÏÏÏÏÏÏÏ
ÏÏÏÏÏÏÏ
ALTITUDE X 1000 FT.
0 100 200 300 360
KIAS (KNOTS)
25
20
15
10
5
0
21,000 FEET
STARTER
ASSISTED
10,000 FEET
N213%
W’MILL
W’MILL
N212%
MODEL CL−600−2A12
AIRPLANE FLIGHT MANUAL
PSP 601−1A−1
DOT Approved
Sep 11/06
44,600/45,100
LIMITATIONS
Page 10
4. POWER PLANT LIMITATIONS (Cont’d)
H. FUEL TEMPERATURE
Take-off with engine fuel temperature indications below 5 °C (41 °F) is
prohibited.
Take-off with a bulk fuel temperature below the following limits is
prohibited.
Fuel Bulk Fuel Take-off Limit Bulk Fuel Freezing Point
ASTM D1655 − JET A −30 °C * −40 °C
ASTM D1655 − JET A1 −37 °C * −47 °C
ASTM D6615 − JET B −40 °C * −50 °C
MIL-DTL-5624 − JP 4 −48 °C * −58 °C
MIL-DTL-5624 − JP 5 −36 °C * −46 °C
MIL-DTL-83133 − JP 8 −40 °C * −50 °C
GB 6537 − No. 3 JET −37 °C * −47 °C
* When OAT is within 5 °C of take-off limit or colder, determine
bulk fuel temperature using a fuel sample from a water drain.
I. FUEL GRADES
Fuel conforming to any of the following specifications are approved for
use. Mixing of fuels is permitted.
Canadian American British
Kerosene Type
CAN 2 − 3.23 ASTM D1655 − JET A D. ENG. RD. 2494
CAN 2 − 3.23 ASTM D1655 − JET A1 D. ENG. RD. 2494
− MIL-DTL-83133 − JP 8 D. ENG. RD. 2453
− MIL-DTL-5624 − JP 5 D. ENG. RD. 2452
Wide Cut Type
CAN 2 − 3.22 ASTM D6615 − JET B D. ENG. RD. 2486
CAN 2 − 3.22 MIL-DTL-5624 − JP 4 D. ENG. RD. 2454
MODEL CL−600−2A12
AIRPLANE FLIGHT MANUAL
PSP 601−1A−1
DOT Approved
Sep 11/06
44,600/45,100
LIMITATIONS
Page 11
4. POWER PLANT LIMITATIONS (Cont’d)
J. FUEL ADDITIVES
The following additives, used individually or in combination, are
approved:
(1) Anti-icing
Anti-icing additives to the latest revision of specifications
MIL-I-27686E or MIL−DTL−85470B or any direct equivalent, at a
concentration of 0.10 to 0.15% by volume.
C A U T I O N
Do not add unblended PRIST additive directly
into the fuel tank, as this may damage fuel
tank components.
Anti-icing Methyl Cellosolve at concentrations of 0.10 to 0.15% by
volume.
(2) Biocide
SOHIO Biobor JF biocide additive at a concentration not in excess of
270 parts per million (20 parts per million elemental boron) for the
initial dose to prevent the growth of micro-organisms. A maintenance
dose of 135 parts per million should be used thereafter.
Kathon FP 1.5 biocide additive at a concentration not in excess of
100 parts per million for the initial dose to prevent the growth of
micro-organisms. A maintenance dose of 50 parts per million should be
used thereafter.
(3) Anti-static
Stadis 450 anti-static additive at a concentration of 5 mg/L.
(4) Corrosion inhibitor
Corrosion inhibitors listed below are approved, by the concentrations
indicated, for hydro-treated fuels only. It is recommended that
corrosion inhibitors, conforming to MlL−I−25017, be blended with the
fuel to provide lubricity. The corrosion inhibitor must be added
after water removal and downstream of any clay filters (these
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：Bombardier_Challenger_00-Limitations（1）(7)