(c)
The master switch or its controls must be installed so that the switch is easily discernible and accessible to a crewmember in .ight.

FAR 27.1365 : Electric cables

(a)
Each electric connecting cable must be of adequate capacity.

(b)
Each cable that would overheat in the event of circuit overload or fault must be at least .ameresistantand may notemitdangerousquantitiesof toxicfumes.

(c)
[Insulation on electrical wire and cable installed in the rotorcraft must be self-extinguishing when tested in accordance with Appendix F, Part I(a)(3) of part 25 of this chapter.]

Amdt. 27-35, E.. 9/8/98
FAR 27.1367 : Switches
Each switch must be–
(a)
Able to carry its rated current;

(b)
Accessible to the crew; and

(c)
Labeled as to operation and the circuit controlled.

66.4 Lights
FAR 27.1381 : Instrument lights
The instrument lights must–
(a)
Make eachinstrument, switch, and otherdevicesfor which they areprovided easily readable; and

(b)
Be installed so that–

(1)
Their direct rays are shielded from the pilot’s eyes; and

(2)
No objectionable re.ections are visible to the pilot.

FAR 27.1383 : Landing lights
(a)
Each required landing or hovering light must be approved.

(b)
Each landing light must be installed so that–

(1)
No objectionableglareis visibletothepilot;

(2)
The pilot is not adversely a.ected by halation; and

(3)
It provides enough light for night operation, including hovering and landing.

′
Elodie Roux. Septembre 2003
Subpart F–Equipment
(c) At least one separate switch must be provided, as applicable–
(1)
For each separately installed landing light; and

(2)
For each group of landing lights installed at a common location.

FAR 27.1385 : Position light system installation
(a)
General. Each part of each position light system must meet the applicable require-ments of this section, and each system as a whole must meet the requirements of Secs. 27.1387 through 27.1397.

(b)
Forwardpositionlights.Forwardpositionlights must consist of a red and agreenlight spaced laterally as far apart as practicable and installed forward on the rotorcraft sothat,with therotorcraftinthe normal .yingposition,theredlightisontheleft side and the green light is on the right side. Each light must be approved.

(c)
Rear position light.The rearpositionlight mustbe a whitelight mounted asfar aft as practicable, and must be approved.

(d)
Circuit. The two forward position lights and the rear position light must make a single circuit.

(e)
Light covers and color .lters.Eachlight coverorcolor .ltermustbeatleast .amere-sistant and may not change color or shape orlose any appreciablelight transmission during normal use.

FAR 27.1387 : Position light system dihedral angles

(a)
[Except asprovidedinparagraph(e)of this section, eachforward and rearposition light must, as installed, show unbroken light within the dihedral angles described in this section.]

(b)
Dihedral angleL(left)isformedby twointersecting verticalplanes,the .rstparallel to the longitudinal axis of the rotorcraft, and the other at 110 degrees to the left of the .rst, as viewed when looking forward along the longitudinal axis.

(c)
DihedralangleR(right)isformedbytwointersecting verticalplanes,the .rstparallel to the longitudinal axis of the rotorcraft, and the other at 110 degrees to the right of the .rst, as viewed when looking forward along the longitudinal axis.

(d)
Dihedral angleA(aft) isformedby twointersecting verticalplanes making angles of 70 degrees to the right and to the left, respectively, to a vertical plane passing through the longitudinal axis, as viewed when looking aft along the longitudinal axis.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：FAA規章 美國聯邦航空規章 Federal Aviation Regulations 4(126)