曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

Appendix 1 to 5.105:  Altimeter System Tests and Inspections
Table I to Appendix 1 to 5.105: Altitude & Equivalent Barometric Pressure
Table II to Appendix 1 to 5.105:   Test Tolerances
Table III to Appendix 1 to 5.105:   Friction
Table IV to Appendix 1 to 5.5105:   Pressure/Altitude Difference
Appendix 2 to 5.105:  Transponder Tests and Inspections
Appendix 3 to 5.105:  VOR Receiver Tests and Inspections
Appendix 1 to 5.165:  Performance Rules: Annual and 100-Hour Inspections
Appendix 1 to 5.215:  Recording of Major Repairs and Major Modifications

 
 SUBPART A:   GENERAL
 5.001  APPLICABILITY
          This Schedule prescribes the requirements for  —
 
(1) Certification of aircraft and aeronautical components;

(2) Issuance of Airworthiness Certificates and other certifications for aeronautical products; 

(3) Continued airworthiness of aircraft and aeronautical components;

(4) Rebuilding and modifications of aircraft and aeronautical components;

(5) Maintenance and preventive maintenance of aircraft and aeronautical components;

(6) Aircraft inspection requirements; and

(7) Air operator aircraft maintenance and inspection requirements.

 
 5.005  DEFINITIONS 
 
For the purpose of the Schedule, the following definitions shall apply —
(1) "Duplicate Inspections" means a Duplicate Inspection of the system that is required wherever any system that can affect the flight path, attitude, or propulsive force of an aircraft is disturbed, including the flight, engine, propeller, and landing gear controls, and the associated operating and support mechanisms, or whenever any defect is reported on such a system;

(i) after re-assembly, or satisfactory operational check, and prior to flight; 

(ii) first carried out and certified by one appropriately type-rated AME and then subsequently carried out and certified by a second appropriately type-rated AME who took no part in the re-assembly;

 

 
(2) "Major modification" is as described in Appendix 1 to 5.005;

(3) "Major repair" is as described in Appendix 2 to 5.005;

(4) "Modification" means the alteration of an aircraft/aeronautical product in conformity with an approved standard;

(5) "Non-certificated Aircraft" means an aircraft, being an ultra-light aircraft, amateur-built; aircraft, kit-plane, or experimental aircraft, which has not been issued with a Type Certificate pursuant to Part V, Regulation 27, of these Regulations and therefore does not qualify for the issue of an Airworthiness Certificate;

(6) "Overhaul" means the restoration of an aircraft/aeronautical product using methods, techniques, and practices acceptable to the Authority, including disassembly, cleaning, and inspection as permitted, repair as necessary, and reassembly; and tested in accordance with approved standards and technical data, or in accordance with current standards and technical data acceptable to the Authority, which have been developed and documented by the State of Design, holder of the type certificate, supplemental type certificate, or a material, part, process, or appliance approval under Parts Manufacturing Authorisation (PMA) or Technical Standard Order (TSO);

(7) "Preventative maintenance"  is as described in Appendix 3 to 5.005;

(8) "Rebuild"  means the restoration of an aircraft/aeronautical product by using methods, techniques, and practices acceptable to the Authority, when it has been disassembled, cleaned, inspected as permitted, repaired as necessary, reassembled, and tested to the same tolerances and limits as a new item, using either new parts or used parts that conform to new part tolerances and limits.  This work will be performed by only the manufacturer or an organization approved by the manufacturer, and authorised by the State of Registry;
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：飛機持續適航 CONTINUING AIRWORTHINESS OF AIRCRAFT(2)